- 您現在的位置：買賣IC網 > PDF目錄383996 > THS4042IDRG4 (Texas Instruments, Inc.) 165-MHz C-STABLE HIGH-SPEED AMPLIFIERS PDF資料下載
參數資料
| 型號： | THS4042IDRG4 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 165-MHz C-STABLE HIGH-SPEED AMPLIFIERS |
| 中文描述： | 165兆赫的C -穩定高速放大器 |
| 文件頁數： | 16/28頁 |
| 文件大?。?/td> | 479K |
| 代理商： | THS4042IDRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
THS4041, THS4042
165-MHz C-STABLE HIGH-SPEED AMPLIFIERS
SLOS237B– MAY 1999 – REVISED FEBRUARY 2000
16
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
driving a capacitive load
Driving capacitive loads with high performance amplifiers is not a problem as long as certain precautions are
taken. The first is to realize that the THS404x has been internally compensated to maximize its bandwidth and
slew rate performance. Typically when the amplifier is compensated in this manner, capacitive loading directly
on the output will decrease the device’s phase margin, leading to high frequency ringing or oscillations.
However, the THS404x has added internal circuitry that senses a capacitive load and adds extra compensation
to the internal dominant pole. As the capacitive load increases, the amplifier remains stable. But, it is not
uncommon to see a small amount of peaking in the frequency response. There are typically two ways to
compensate for this. The first is to simply increase the gain of the amplifier. This helps by increasing the phase
margin to keep peaking minimized. The second is to place an isolation resistor in series with the output of the
amplifier, as shown in Figure 65. A minimum value of 20
should work well for most applications. For example,
in 75-
transmission systems, setting the series resistor value to 75
both isolates any capacitance loading
and provides the proper line impedance matching at the source end. For more information about driving
capacitive loads, refer to the Output Resistance and Capacitancesection of the Parasitic Capacitance in Op
Amp Circuits Application Report(literature number: SLOA013).
+
_
THS404x
CLOAD
1.3 k
Input
Output
1.3 k
20
Figure 65. Driving a Capacitive Load for Extra Stability
offset nulling
The THS404x has very low input offset voltage for a high-speed amplifier. However, if additional correction is
required, an offset nulling function has been provided on the THS4041. The input offset can be adjusted by
placing a potentiometer between terminals 1 and 8 of the device and tying the wiper to the negative supply. This
is shown in Figure 66.
_
+
THS4041
VCC–
VCC+
0.1
μ
F
0.1
μ
F
10 k
Figure 66. Offset Nulling Schematic
相關PDF資料 |
PDF描述 |
|---|---|
| THS4041D | 165-MHz C-STABLE HIGH-SPEED AMPLIFIERS |
| THS4041DGN | 165-MHz C-STABLE HIGH-SPEED AMPLIFIERS |
| THS4041EVM | 165-MHz C-STABLE HIGH-SPEED AMPLIFIERS |
| THS4042D | 165-MHz C-STABLE HIGH-SPEED AMPLIFIERS |
| THS4042DGN | 165-MHz C-STABLE HIGH-SPEED AMPLIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS4051 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:70-MHz HIGH-SPEED AMPLIFIERS |
| THS4051CD | 功能描述:高速運算放大器 70MHz High Speed RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4051CDG4 | 功能描述:高速運算放大器 70-MHz Low-Cost Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4051CDGN | 功能描述:高速運算放大器 70-MHz Low-Cost Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| THS4051CDGNG4 | 功能描述:高速運算放大器 70-MHz Low-Cost Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。