參數資料
型號： THS4041CDGNG4
廠商： Texas Instruments, Inc.
英文描述： 165-MHz C-STABLE HIGH-SPEED AMPLIFIERS
中文描述： 165兆赫的C -穩定高速放大器
文件頁數： 16/28頁
文件大小： 479K
代理商： THS4041CDGNG4
THS4041, THS4042
165-MHz C-STABLE HIGH-SPEED AMPLIFIERS
SLOS237B– MAY 1999 – REVISED FEBRUARY 2000
16
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
driving a capacitive load
Driving capacitive loads with high performance amplifiers is not a problem as long as certain precautions are
taken. The first is to realize that the THS404x has been internally compensated to maximize its bandwidth and
slew rate performance. Typically when the amplifier is compensated in this manner, capacitive loading directly
on the output will decrease the device’s phase margin, leading to high frequency ringing or oscillations.
However, the THS404x has added internal circuitry that senses a capacitive load and adds extra compensation
to the internal dominant pole. As the capacitive load increases, the amplifier remains stable. But, it is not
uncommon to see a small amount of peaking in the frequency response. There are typically two ways to
compensate for this. The first is to simply increase the gain of the amplifier. This helps by increasing the phase
margin to keep peaking minimized. The second is to place an isolation resistor in series with the output of the
amplifier, as shown in Figure 65. A minimum value of 20
should work well for most applications. For example,
in 75-
transmission systems, setting the series resistor value to 75
both isolates any capacitance loading
and provides the proper line impedance matching at the source end. For more information about driving
capacitive loads, refer to the Output Resistance and Capacitancesection of the Parasitic Capacitance in Op
Amp Circuits Application Report(literature number: SLOA013).
+
_
THS404x
CLOAD
1.3 k
Input
Output
1.3 k
20
Figure 65. Driving a Capacitive Load for Extra Stability
offset nulling
The THS404x has very low input offset voltage for a high-speed amplifier. However, if additional correction is
required, an offset nulling function has been provided on the THS4041. The input offset can be adjusted by
placing a potentiometer between terminals 1 and 8 of the device and tying the wiper to the negative supply. This
is shown in Figure 66.
_
+
THS4041
VCC–
VCC+
0.1
μ
F
0.1
μ
F
10 k
Figure 66. Offset Nulling Schematic
相關PDF資料
PDF描述
THS4061D 180-MHz HIGH-SPEED AMPLIFIERS
THS4061JG 180-MHz HIGH-SPEED AMPLIFIERS
THS4061DGN 180-MHz HIGH-SPEED AMPLIFIERS
THS4061EVM 180-MHz HIGH-SPEED AMPLIFIERS
THS4061FK 180-MHz HIGH-SPEED AMPLIFIERS
相關代理商/技術參數
參數描述
THS4041CDGNR 功能描述:高速運算放大器 165-MHz C-Stable Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS4041CDGNRG4 功能描述:高速運算放大器 165-MHz C-Stable Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS4041CDR 功能描述:高速運算放大器 165-MHz C-Stable Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS4041CDRG4 功能描述:高速運算放大器 165-MHz C-Stable Volt-Feedback Amp RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS4041D 制造商:TI 制造商全稱:Texas Instruments 功能描述:165-MHz C-STABLE HIGH-SPEED AMPLIFIERS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*