<big id="fzyne"><strong id="fzyne"><table id="fzyne"></table></strong></big>
<ins id="fzyne"></ins>
<thead id="fzyne"><sup id="fzyne"><dl id="fzyne"></dl></sup></thead>
  •         
    
    
    參數資料
    型號: THS1209IDA
    廠商: TEXAS INSTRUMENTS INC
    元件分類: ADC
    英文描述: 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
    封裝: GREEN, PLASTIC, TSSOP-32
    文件頁數: 22/33頁
    文件大小: 312K
    代理商: THS1209IDA
    THS1209
    SLAS288B – JULY 2000 – REVISED DECEMBER 2002
    www.ti.com
    29
    DC COUPLING
    An operational amplifier can be configured to shift the signal level according to the analog input voltage range of the
    THS1209. The analog input voltage range of the THS1209 goes from 1.5 V to 3.5 V. An op-amp can be used as
    shown in Figure 35.
    Figure 35 shows an example where the analog input signal in the range from –1 V up to 1 V is shifted by an
    operational amplifier to the analog input range of the THS1209 (1.5 V to 3.5 V). The operational amplifier is configured
    as an inverting amplifier with a gain of –1. The required dc voltage of 1.25 V at the noninverting input is derived from
    the 2.5-V output reference REFOUT of the THS1209 by using a resistor divider. Therefore, the op-amp output voltage
    is centered at 2.5 V. The 10
    F tantalum capacitor is required for bypassing REFOUT. REFIN of the THS1209 must
    be connected directly to REFOUT in single-ended mode. The use of ratio matched, thin-film resistor networks
    minimizes gain and offset errors.
    _
    +
    5 V
    R1
    RS
    3.5 V
    2.5 V
    1.5 V
    THS1209
    AINP
    REFOUT
    R2
    1.25 V
    1 V
    0 V
    –1 V
    REFIN
    +
    C
    10
    F
    Figure 35. Level-Shift for DC-Coupled Input
    DIFFERENTIAL MODE OF OPERATION
    For the differential mode of operation, a conversion from single-ended to differential is required. A conversion to
    differential signals can be achieved by using an RF-transformer, which provides a center tap. Best performance is
    achieved in differential mode.
    THS1209
    AINP
    AINM
    REFOUT
    C
    R
    200
    49.9
    Mini Circuits
    T4–1
    +
    10
    F
    Figure 36. Transformer Coupled Input
    相關PDF資料
    PDF描述
    THS1209CDA 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
    THS1209CDAG4 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
    THS1209IDAG4 2-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
    THS1215CDWRG4 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28
    THS1215IDWRG4 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28
    相關代理商/技術參數
    參數描述
    THS1209IDAG4 功能描述:模數轉換器 - ADC 12 Bit 8 MSPS Dual Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
    THS121 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:HIGH STABILITY MOTOR CONTROL. DIGITAL TACHOMETER. CRANK SHAFT POSITION SENSOR.
    THS1215 制造商:TI 制造商全稱:Texas Instruments 功能描述:3.3-V, 12-BIT, 15 MSPS, LOW-POWER ANALOG-TO-DIGITAL CONVERTER WITH POWER DOWN
    THS1215CDW 功能描述:模數轉換器 - ADC 12-Bit 15 MSPS w/Low Pwr & exc ENOB RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
    THS1215CDWG4 功能描述:模數轉換器 - ADC 12-Bit 15 MSPS w/Low Pwr & exc ENOB RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32