參數資料
型號： THS1031IPWG4
廠商： TEXAS INSTRUMENTS INC
元件分類： ADC
英文描述： 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28
封裝： GREEN, PLASTIC, TSSOP-28
文件頁數： 21/41頁
文件大?。?/td> 728K
代理商： THS1031IPWG4
THS1031
3-V TO 5.5-V, 10-BIT, 30 MSPS
CMOS ANALOG-TO-DIGITAL CONVERTER
SLAS242E – NOVEMBER 1999 – REVISED MARCH 2002
28
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
driving the THS1301 analog inputs
driving AIN
Figure 32 shows an equivalent circuit for the THS1031 AIN pin. The load presented to the system at the AIN
pin comprises the switched input sampling capacitor, CSAMPLE, and various stray capacitances, CP1 and CP2.
C1
8 pF
AVDD
AGND
CLK
C2
1.2 pF
CSAMPLE
VLAST
AIN
_
+
Figure 32. Equivalent Circuit of Analog Input AIN
In any single-ended input mode, VLAST = the average of the previously sampled voltage at AIN and the average
of the voltages on pins REFTS and REFBS. In any differential mode, VLAST = the common mode input voltage.
The external source driving AIN must be able to charge and settle into CSAMPLE and the CP1 and CP2 strays
to within 0.5 LSB error while sampling (CLK pin low) to achieve full ADC resolution.
AIN input current and input load modeling
When CLK goes low, the source driving AIN must charge the total switched capacitance CS = CSAMPLE + CP2.
The total charge transferred depends on the voltage at AIN and is given by
Q
CHARGING +
(AIN
* V
LAST
)
C
S
.
For a fixed voltage at AIN, so that AIN and VLAST do not change between samples, the maximum amount of
charge transfer occurs at AIN = FS– (charging current flows out of THS1030) and AIN = FS+ (current flows into
THS1030). If AIN is held at the voltage FS+, VLAST = [(FS+) + VM]/2, giving a maximum transferred charge:
Q(FS)
+
(FS
)) * [(FS )) ) VM]
2
C
S +
[(FS
)) * VM]
C
S
2
+ (1 4 of the input voltage span)
C
S
If the input voltage changes between samples, then the maximum possible charge transfer is
Q(max)
+ 3
Q(FS)
which occurs for a full-scale input change (FS+ to FS– or FS– to FS+) between samples.
The charging current pulses can make the AIN source jump or ring, especially if the source is slightly inductive
at high frequencies. Inserting a small series resistor of 20
or less in the input path can damp source ringing.
See Figure 33. This resistor can be made larger than 20
if reduced input bandwidth or distortion performance
is acceptable.
(9)
(10)
(11)
相關PDF資料
PDF描述
THS1031IPWR 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28
THS1031CPWRG4 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28
THS1031IDW 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28
THS1031CPW 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28
THS1031CDW 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28
相關代理商/技術參數
參數描述
THS1031IPWR 功能描述:模數轉換器 - ADC 10-Bit 30 MSPS 1-Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
THS1031IPWRG4 功能描述:模數轉換器 - ADC 10-Bit 30 MSPS 1-Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
THS1031SOIC 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.7 V . 5.5 V, 10-BIT, 30 MSPS CMOS ANALOG-TO-DIGITAL CONVERTER
THS1031TSSOP 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.7 V . 5.5 V, 10-BIT, 30 MSPS CMOS ANALOG-TO-DIGITAL CONVERTER
THS10330RJ 功能描述:線繞電阻器 - 底架安裝 THS10 330R 5% RoHS:否 制造商:Vishay/Dale 電阻:7 Ohms 容差:1 % 功率額定值:100 W 溫度系數:50 PPM / C 系列:RH 工作溫度范圍:- 55 C to + 250 C 尺寸:46.02 mm Dia. x 46.02 mm W x 88.9 mm L x 44.45 mm H 封裝:Bulk 產品:Power Resistors Wirewound Aluminum Housed
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*