- 您現在的位置：買賣IC網 > PDF目錄384974 > THS1009CDAR (Texas Instruments, Inc.) 10-BIT, 2 ANALOG INPUT, 8 MSPS, SIMULTANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER PDF資料下載
參數資料
| 型號： | THS1009CDAR |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 10-BIT, 2 ANALOG INPUT, 8 MSPS, SIMULTANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
| 中文描述： | 10位，2個模擬輸入，8 MSPS的同步采樣模擬數字轉換器 |
| 文件頁數： | 5/31頁 |
| 文件大?。?/td> | 235K |
| 代理商： | THS1009CDAR |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
SLAS287A
–
AUGUST 2000
–
REVISED DECEMBER 2002
www.ti.com
5
Terminal Functions
TERMINAL
NAME
I/O
DESCRIPTION
NO.
AINP
30
I
Analog input, single-ended or positive input of differential channel A
AINM
29
I
Analog input, single-ended or negative input of differential channel A
AVDD
AGND
23
I
Analog supply voltage
24
I
Analog ground
BVDD
BGND
7
I
Digital supply voltage for buffer
8
I
Digital ground for buffer
CONV_CLK
15
I
Digital input. This input is the conversion clock input.
CS0
22
I
Chip select input (active low)
CS1
21
I
Chip select input (active high)
SYNC
16
O
Synchronization output. This signal indicates in a multichannel operation that data of channel A is brought to the
digital output and can therefore be used for synchronization.
DGND
17
I
Digital ground. Ground reference for digital circuitry.
DVDD
D0
–
D9
18
I
Digital supply voltage
1
–
6,
9
–
12
I/
O/Z
Digital input, output; D0 = LSB
RA0
13
I
Digital input. RA0 is used as an address line (RA0) for the control register. This is required for writing to control
register 0 and control register 1. See Table 7.
RA1
14
I
Digital input. RA1 is used as an address line (RA1) for the control register. This is required for writing to control
register 0 and control register 1. See Table 7.
NC
32
O
Not connected
REFIN
28
I
Common-mode reference input for the analog input channels. It is recommended that this pin be connected to the
reference output REFOUT.
REFP
26
I
Reference input, requires a bypass capacitor of 10
μ
F to AGND in order to bypass the internal reference voltage.
An external reference voltage at this input can be applied. This option can be programmed through control
register 0. See Table 8.
Reference input, requires a bypass capacitor of 10
μ
F to AGND in order to bypass the internal reference voltage.
An external reference voltage at this input can be applied. This option can be programmed through control
register 0. See Table 8.
REFM
25
I
RESET
31
I
Hardware reset of the THS1009. Sets the control register to default values.
Analog fixed reference output voltage of 2.5 V. Sink and source capability of 250
μ
A. The reference output requires
a capacitor of 10
μ
F to AGND for filtering and stability.
The RD input is used only if the WR input is configured as a write only input. In this case, it is a digital input, active
low as a data read select from the processor. See timing section.
REFOUT
27
O
RD(1)
19
I
WR (R/W)(1)
20
I
This input is programmable. It functions as a read-write input (R/W) and can also be configured as a write-only input
(WR), which is active low and used as data write select from the processor. In this case, the RD input is used as a
read input from the processor. See timing section.
(1)The start-conditions of RD and WR (R/W) are unknown. The first access to the ADC has to be a write access to initialize the ADC.
相關PDF資料 |
PDF描述 |
|---|---|
| THS1009CDARG4 | 10-BIT, 2 ANALOG INPUT, 8 MSPS, SIMULTANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
| THS1009IDAR | 10-BIT, 2 ANALOG INPUT, 8 MSPS, SIMULTANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
| THS1009IDARG4 | 10-BIT, 2 ANALOG INPUT, 8 MSPS, SIMULTANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
| THS4140CDGK | HIGH SPEED FULLY DIFFERENTIAL I/O AMPLIFIERS |
| THS4271DGKRG4 | LOW NOISE, HIGH SLEW RATE, UNITY GAIN STABLE VOLTAGE FREEBACK AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS1009CDARG4 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT, 2 ANALOG INPUT, 8 MSPS, SIMULTANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
| THS1009EVM | 功能描述:EVALUATION MODULE FOR THS1009 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| THS1009IDA | 功能描述:模數轉換器 - ADC 10 BIT QUAD ADC w/o RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1009IDAG4 | 功能描述:模數轉換器 - ADC 10-Bit 8 MSPS Dual Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1009IDAR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT, 2 ANALOG INPUT, 8 MSPS, SIMULTANEOUS SAMPLING ANALOG-TO-DIGITAL CONVERTER |
發布緊急采購，3分鐘左右您將得到回復。