- 您現在的位置：買賣IC網 > PDF目錄98216 > THMC10DBQ (TEXAS INSTRUMENTS INC) SPECIALTY ANALOG CIRCUIT, PDSO16 PDF資料下載
參數資料
| 型號： | THMC10DBQ |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | PLASTIC, SSOP-16 |
| 文件頁數： | 6/22頁 |
| 文件大?。?/td> | 312K |
| 代理商： | THMC10DBQ |
THMC10
REMOTE/LOCAL TEMPERATURE MONITOR
WITH SMBus INTERFACE
SLIS089 – DECEMBER 1999
14
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
PC board layout considerations
D Place the THMC10 as close as practical to the remote diode. In a noisy environment, such as a computer
motherboard, this distance can be 4 inches to 8 inches (typical) or more, as long as the worst noise sources
(such as CRTs, clock generators, memory buses, and ISA/PCI buses) are avoided.
D Route the DXP–DXN lines away from the deflection coils of a CRT. Also, avoid routing the traces across
a fast memory bus which can easily introduce 30
°C error even with good filtering. Otherwise, most noise
sources are fairly benign.
D Route the DXP and DXN traces in parallel and in close proximity to each other, away from any high-voltage
traces such as 12 Vdc. Leakage currents from PC board contamination must be be taken into consideration,
since a 20-M
leakage path from DXP to ground causes about 1°C error.
D Connect guard traces to GND on either side of the DXP–DXN traces (Figure 7). With guard traces in place,
routing near high-voltage traces is not an issue.
D Route through as few vias and crossunders as possible to minimize copper/solder thermocouple effects.
D When introducing a thermocouple, insure that both the DXP and the DXN paths have matching
thermocouples. In general, PC board induced thermocouples are not a serious problem. A copper-solder
thermocouple exhibits 3
V/°C, and it takes about 200 V of voltage error at DXP–DXN to cause a 1°C
measurement error. Hence, most parasitic thermocouple errors are swamped out.
D Use wide traces. Narrow traces are more inductive and tend to pick up radiated noise. The 10-mil widths
and spacings recommended in Figure 7 are not absolutely necessary as they offer only a minor
improvement in leakage and noise, but usage is recommended where practical.
D Copper can not be used as an EMI shield and only ferrous materials such as steel work well. Placing a
copper ground plane between the DXP–DXN traces and traces carrying high-frequency noise signals does
not help reduce EMI.
PC board layout checklist
D Place the THMC10 as close as possible to the remote diode.
D Keep traces away from high voltages (12 V bus).
D Keep traces away from fast data/memory buses and CRTs.
D Use recommended trace widths and spacings.
D Place a ground plane under the traces.
D Use guard traces flanking DXP and DXN and connecting to GND.
D Place the noise filter and the 0.1-F VDD bypass capacitors close to the THMC10.
相關PDF資料 |
PDF描述 |
|---|---|
| THMC45 | BRUSHLESS DC MOTOR CONTROLLER, 0.25 A, PDSO8 |
| THS0842IPFB | 2-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| THS0842IPFBG4 | 2-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP48 |
| THS10064CDA | 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
| THS10064IDA | 4-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THMC10DBQR | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述: |
| THMC10SSOPDBQ | 制造商:TI 制造商全稱:Texas Instruments 功能描述:REMOTE/LOCAL TEMPERATURE MONITOR WITH SMBus INTERFACE |
| THMC40 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:VARIABLE SPEED 12-VDC BRUSHLESS FAN MOTOR DRIVERS |
| THMC40SOPD | 制造商:TI 制造商全稱:Texas Instruments 功能描述:VARIABLE SPEED 12-VDC BRUSHLESS FAN MOTOR DRIVERS |
| THMC41 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:VARIABLE SPEED 12-VDC BRUSHLESS FAN MOTOR DRIVERS |
發布緊急采購，3分鐘左右您將得到回復。