- 您現在的位置：買賣IC網 > PDF目錄384971 > TFDU6108 (Vishay Intertechnology,Inc.) Fast Infrared Transceiver Module (4 Mbit/s), IrDA Serial Interface Compatible, 2.7 V to 5.5 V Supply Voltage Range PDF資料下載
參數資料
| 型號： | TFDU6108 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Fast Infrared Transceiver Module (4 Mbit/s), IrDA Serial Interface Compatible, 2.7 V to 5.5 V Supply Voltage Range |
| 中文描述： | 快速紅外收發器模塊（4兆位/秒），紅外串行接口兼容，2.7 V至5.5 V電源電壓范圍 |
| 文件頁數： | 20/27頁 |
| 文件大?。?/td> | 940K |
| 代理商： | TFDU6108 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
www.vishay.com
20
Document Number 82537
Rev. 1.6, 25-Jun-04
VISHAY
TFDU6108
Vishay Semiconductors
Appendix C
Serial Interface (SIF) Programming Guide
The SIF port of this module allow an IR controller to
communicate with it, get module ID and capability
information, implement receiver bandwidth mode
switching, LED power control, shutdown and some
other functions.
This interface requires three signals: a clock line
(SCLK) that is used for timing, and two unidirectional
lines multiplexed with the transmitter (Txd, write) and
receiver (Rxd, read) infrared signal lines.
The supported programming sequence formats are
listed below:
one-byte special commands
two-byte write commands
two-byte read commands
three-byte read commands
The one-byte special command sequences are
reserved for time-critical actions, while the two-byte
write command is predominantly used to set basic
transceiver characteristics. More information can be
found in the IrDA document "Serial Interface for
Transceiver Control, v 1.0a" on IrDA.org web site.
Serial Interface Timing Specifications
In general, serial interface programming sequences
are similar to any clocked-data protocol:
there is a range of acceptable clock rates, mea-
sured from rising edge to rising edge
there is a minimum data setup time before clock ris-
ing edges
there is a minimum data hold time after clock rising
edges
Recommended programming timing:
(4 kHz <) fclk < 8 MHz (4 kHz is a recommended
value, according to the Serial Interface Standard
quasi-static programming is possible)
TCLK > 125 ns (< 250
μ
s, see the remark for quasi-
static programming above)
Tsetup > 10 ns
Thold > 10 ns
The timing diagrams below show the setup and hold
time for Serial Interface programming sequences:
Protocol Specifications
The serial interface protocol is a command-based
communication standard and allows for the communi-
cation between controller and transceiver by way of
serial programming sequences on the clock (SCLK),
transmit (TX), and receive (RX) lines. The SCLK line
is used as a clocking signal and the transmit/receive
lines are used to write/read data information. The pro-
tocol requires all transceivers to implement the write
commands, but does not require the read-portion of
the protocol to be implemented (though all transceiv-
ers must at least follow the various commands, even
if they perform no internal action as a result). This
serial interface follows but does not support all read/
write commands or extended commands, supporting
only the special commands and basic write/read com-
mands.
Write commands to the transceiver take place on the
SCLK and TX lines and may make use of the RX line
for answer back purposes.
A command may be directed to a single transceiver
on the SCLK, TX and RX bus by specifying a unique
three-bit transceiver address, or a command may be
directed to all transceivers on the bus by way of a spe-
cial three-bit broadcast address code. The Vishay
VFIR transceiver TFDU8108 will respond to trans-
ceiver address 010 and the broadcast address 111
only, and follows but ignores all other transceiver
addresses. The transceiver address of Vishay FIR
module TFDU6108 is 001.
All commands have a common \"header\" or series of
leading bits which take the form shown below.
SCLK
TX
125 ns < Tclk
s
Tsetup > 10 ns
Thold > 10 ns
18496
0
1
1/0 R0 R1 R2 R3 A0 A1 A2
...
Sync
Bits
Register
or Code
Transceiver
Address
1=Write
0=Read
first bit sent to
transceiver
last bit sent to
transceiver
18497
相關PDF資料 |
PDF描述 |
|---|---|
| TFDU6108-TR3 | Fast Infrared Transceiver Module (4 Mbit/s), IrDA Serial Interface Compatible, 2.7 V to 5.5 V Supply Voltage Range |
| TFDU6108-TT3 | Fast Infrared Transceiver Module (4 Mbit/s), IrDA Serial Interface Compatible, 2.7 V to 5.5 V Supply Voltage Range |
| TFDU8108 | Very Fast IrDA in Standard package |
| TFK3080D | npn silicon tripleton power transistor |
| TFMM5560 | Photo Modules for PCM Remote Control Systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TFDU6108-TR3 | 功能描述:紅外收發器 FIR 4Mbit/s 2.7-5.5V Op Voltage RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
| TFDU6108-TR3 19 | 制造商:Vishay Angstrohm 功能描述:IRDA TRANSCEIVER FIR BABYFACE MOLD- |
| TFDU6108-TR3 19 | 功能描述:紅外收發器 IRDA TRANSCEIVER FIR BABYFACE MOLD- RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
| TFDU6108-TR319 | 功能描述:紅外收發器 FIR 4Mbit/s 2.7-5.5V Op Voltage RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
| TFDU6108-TT3 | 功能描述:紅外收發器 FIR 4Mbit/s 2.7-5.5V Op Voltage RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。