- 您現在的位置：買賣IC網 > PDF目錄384971 > TFDU5103 (Vishay Intertechnology,Inc.) Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation PDF資料下載
參數資料
| 型號： | TFDU5103 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation |
| 中文描述： | 快速紅外收發器模塊（，補償1.152兆位/秒）為2.7 V至5.5 V工作電壓 |
| 文件頁數： | 8/16頁 |
| 文件大小： | 420K |
| 代理商： | TFDU5103 |
www.vishay.com
8
Document Number 82618
Rev. 1.2, 24-Jun-04
VISHAY
TFDU5103
Vishay Semiconductors
Recommended Circuit Diagram
Vishay Semiconductors transceivers integrate a sen-
sitive receiver and a built-in power driver. The combi-
nation of both needs a careful circuit board layout.
The use of thin, long, resistive and inductive wiring
should be avoided. The inputs (Txd, SD, Mode) and
the output Rxd should be directly (DC) coupled to the
I/O circuit.
The capacitor C1 is buffering the supply voltage and
reduces the influence of the inductance of the power
supply line. This one should be a Tantalum or other
fast capacitor to guarantee the fast rise time of the
IRED current. The resistor R1 is only necessary for
higher operating voltages and elevated temperatures,
see derating curve in figure 7, to avoid too high inter-
nal power dissipation.
The capacitor C2 combined with the resistor R2 is the
low pass filter for smoothing the supply voltage. R2,
C1 and C2 are optional and dependent on the quality
of the supply voltage V
CCx
and injected noise. An
unstable power supply with dropping voltage during
transmission may reduce sensitivity (and transmis-
sion range) of the transceiver.
The placement of these parts is critical. It is strongly
recommended to position C2 as near as possible to
the transceiver power supply pins. An Tantalum
capacitor should be used for C1 while a ceramic
capacitor is used for C2.
In addition, when connecting the described circuit to
the power supply, low impedance wiring should be
used.
When extended wiring is used the inductance of the
power supply can cause dynamically a voltage drop
at V
CC2
. Often some power supplies are not apply to
follow the fast current is rise time. In that case another
4.7
μ
F (type, see table under C1) at V
CC2
will be help-
ful.
Keep in mind that basic RF-design rules for circuit
design should be taken into account. Especially
longer signal lines should not be used without termi-
nation. See e.g. "The Art of Electronics" by Paul
Horowitz and Winfield Hill, 1989, Cambridge Univer-
sity Press, ISBN: 0521370957.
Recommended Application Circuit Components
Figure 1. Recommended Application Circuit
Test circuit
Input Signal
- total pulse duration
- duty factor
tp(tot) =
δ
= 0.00
ˇ
Component
C1
C2
R1
Recommended Value
4.7
μ
F, 16 V
0.1
μ
F, Ceramic
Vishay Part Number
293D 475X9 016B
VJ 1206 Y 104 J XXMT
e.g. 2 x CRCW-1206-1R0-F-RT1
5 V supply voltage:
2
, 0.25 W ( recommended using
two 1
, 0.125 W resistor in series)
3.3 V supply voltage:
no resistor necessary, the internal
controller is able to control the current
47
, 0.125 W
R2
CRCW-1206-47R0-F-RT1
相關PDF資料 |
PDF描述 |
|---|---|
| TFDU5103-TR3 | Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation |
| TFDU5103-TT3 | Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation |
| TFDU5107 | Integrated Low Profile Transceiver Module for Telecom Applications |
| TFDU5107-TR3 | Integrated Low Profile Transceiver Module for Telecom Applications |
| TFDU5107-TT3 | Integrated Low Profile Transceiver Module for Telecom Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TFDU5103-TR3 | 功能描述:紅外收發器 MIR 1.152 Mbits/s RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
| TFDU5103-TR3 19 | 制造商:Vishay Angstrohm 功能描述:IRDA TRANSCEIVER MIR BABYFACE MOLD- |
| TFDU5103-TT3 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation |
| TFDU5107 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Low Profile Transceiver Module for Telecom Applications 9.6 kbit/s to 1.152 Mbit/s Data Transmission Rate |
| TFDU5107_05 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Low Profile Transceiver Module for Telecom Applications 9.6 kbit/s to 1.152 Mbit/s Data Transmission Rate |
發布緊急采購，3分鐘左右您將得到回復。