- 您現在的位置：買賣IC網 > PDF目錄384971 > TFDU4300 (Vishay Intertechnology,Inc.) Standard IrDA with Low Power Consumption PDF資料下載
參數資料
| 型號： | TFDU4300 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Standard IrDA with Low Power Consumption |
| 中文描述： | 標準的IrDA低功耗 |
| 文件頁數： | 8/15頁 |
| 文件大?。?/td> | 396K |
| 代理商： | TFDU4300 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
www.vishay.com
8
Document Number 82614
Rev. 1.4, 26-Jan-04
VISHAY
TFDU4300
Vishay Semiconductors
Recommended Circuit Diagram
Operated with a clean low impedance power supply
the TFDU4300 needs no additional external compo-
nents. However, depending on the entire system
design and board layout, additional components may
be required (see figure 1).
Recommended Application Circuit
The capacitor C1 is buffering the supply voltage and
eliminates the inductance of the power supply line.
This one should be a Tantalum or other fast capacitor
to guarantee the fast rise time of the IRED current.
The resistor R1 is the current limiting resistor, which
may be used to reduce the operating current to levels
below the specified controlled values for saving bat-
tery power.
Vishay’s transceivers integrate a sensitive receiver
and a built-in power driver. The combination of both
needs a careful circuit board layout. The use of thin,
long, resistive and inductive wiring should be avoided.
The inputs (Txd, SD) and the output Rxd should be
directly connected (DC - coupled) to the I/O circuit.
The capacitor C2 combined with the resistor R2 is the
low pass filter for smoothing the supply voltage. R2,
C1 and C2 are optional and dependent on the quality
of the supply voltages V
CC1
and injected noise. An
unstable power supply with dropping voltage during
transmission may reduce the sensitivity (and trans-
mission range) of the transceiver.
The placement of these parts is critical. It is strongly
recommended to position C2 as close as possible to
the transceiver power supply pins. An Tantalum
capacitor should be used for C1 while a ceramic
capacitor is used for C2.
In addition, when connecting the described circuit to
the power supply, low impedance wiring should be
used.
When extended wiring is used the inductance of the
power supply can cause dynamically a voltage drop
at V
CC2
. Often some power supplies are not apply to
follow the fast current rise time. In that case another
4.7
μ
F (type, see table under C1) at V
CC2
will be help-
ful.
Under extreme EMI conditions as placing an RF-
transmitter antenna on top of the transceiver, we rec-
ommend to protect all inputs by a low-pass filter, as a
minimum a 12 pF capacitor, especially at the Rxd
port. The transceiver itself withstands EMI at GSM
frequencies above 300 V/m. When interference is
observed, it is picked up by the wiring to the inputs. It
is verified by DPI (direct power injection) measure-
ments that as long as the interfering RF - voltage is
below the logic threshold levels of the inputs and
equivalent levels at the outputs no interference is
expected.
Figure 2 and figure 3 show examples for circuit dia-
grams to work with low voltage logic and using the
transceiver when V
CC1
= V
logic
, just connecting the
responsible pins to each other.
Figure 1. Recommended Application Circuit
IRED Anode
V
cc
Ground
SD
Txd
Rxd
V
CC
1
GND
SD
Txd
Rxd
R1
R2
C1
C2
18096
Vlogic
Mode
V
CC
2
IRED Cathode
相關PDF資料 |
PDF描述 |
|---|---|
| TFDU5103 | Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation |
| TFDU5103-TR3 | Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation |
| TFDU5103-TT3 | Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation |
| TFDU5107 | Integrated Low Profile Transceiver Module for Telecom Applications |
| TFDU5107-TR3 | Integrated Low Profile Transceiver Module for Telecom Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TFDU4300 | 制造商:Vishay Intertechnologies 功能描述:IRDA TRANSCIEVER |
| TFDU4300A | 功能描述:TXRX IRDA 115.2KBIT 2.5MM 8-SMD RoHS:是 類別:傳感器，轉換器 >> IrDA 收發器模塊 系列:- 產品變化通告:Product Discontinuation 30/Sept/2009 產品目錄繪圖:GP2W Series 標準包裝:1 系列:* 數據速率:115.2kbs（SIR） 電源電壓:2.4 V ~ 3.6 V 無效電流，標準值@ 25° C:70µA 通信距離，低功率:20cm 方向:側視圖 工作溫度:-40°C ~ 85°C 尺寸:8.3mm x 2.1mm x 1.7mm 標準:IrPHY 1.4 關機:* 包裝:Digi-Reel® 其它名稱:425-2614-6 |
| TFDU4300-TR1 | 功能描述:紅外收發器 SIR 115.2 kbits/s 2.4-5.5V Op Voltage RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
| TFDU4300-TR1 | 制造商:Vishay Semiconductors 功能描述:IrDA - Infrared Transceiver |
| TFDU4300-TR3 | 功能描述:紅外收發器 SIR 115.2 kbits/s RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。