- 您現在的位置：買賣IC網 > PDF目錄384970 > TFDU4204 (Vishay Intertechnology,Inc.) Integrated Low Profile Transceiver Module for Telecom Applications - IrDA Standard PDF資料下載
參數資料
| 型號： | TFDU4204 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Integrated Low Profile Transceiver Module for Telecom Applications - IrDA Standard |
| 中文描述： | 集成的收發器模塊超薄電信應用-紅外標準 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 147K |
| 代理商： | TFDU4204 |
TFDU4203
Vishay Semiconductors
Rev. A1.1, 13-Feb-03
10 (12)
www.vishay.com
Document Number 82542
Appendix
Application Hints
The TFDU4203 does not need any external
components when operated at a “clean“ power supply.
In a more noisy ambient it is recommended to add a
capacitor C1 (4.7 F Tantalum) and a resistor
R1 (
≤
3
)
for noise suppression. In addition the
capacitor is needed to prevent a pulse distortion when
the power supply is not able to generate the peak
currents or inductive wiring is used. A combination of
a tantalum with a ceramics capacitor will be efficient to
attenuate both, RF and LF if RF noise is present. The
value is dependent on the power supply quality. A good
choice is between 4.7 F and 10 F.
Recommended Circuit Diagram
TFDU4203
R1
Vcc
Rxd
C1
GND
SD
Txd
5, 6
8
3
7
4
GND
SD
Rxd
Txd
V
CC
R2
1, 2 IRED Cathode
Shut down
To shut down the TFDU4103 into a standby mode the
SD pin has to be set active.
Latency
The receiver is in specified conditions after the defined
latency. In a UART related application after that time
(typically 50
μ
s) the receiver buffer of the UART must
be cleared. Therefore the transceiver has to wait at
least the specified latency after receiving the last bit
before starting the transmission to be sure that the
corresponding receiver is in a defined state.
For more application circuits, see IrDC Design Guide
and TOIM3...–series data.
Table 1. Recommended Application Circuit Components *)
Component
C1
4.7 F, 16 V
R1
5
max
*)
This is a recommendation for a combination to start with to exclude power supply effects.
Optimum, from a costs point of view, to work without both.
Recommended Value
Vishay Part Number
293D 475X9 016B 2T
相關PDF資料 |
PDF描述 |
|---|---|
| TFDU4203 | Integrated Low Profile Transceiver Module for Telecom Applications - IrDA Standard |
| TFDU4203-TR1 | Integrated Low Profile Transceiver Module for Telecom Applications ? IrDA Standard |
| TFDU4203-TR3 | Integrated Low Profile Transceiver Module for Telecom Applications ? IrDA Standard |
| TFDU4201 | D52 - BACKSHELL ENVIRON EMI-RFI STRT MIL |
| TFDU4202 | CONNECTOR ACCESSORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TFDU4300 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Infrared Transceiver Module (SIR, 115.2 kbit/s) |
| TFDU4300 | 制造商:Vishay Intertechnologies 功能描述:IRDA TRANSCIEVER |
| TFDU4300A | 功能描述:TXRX IRDA 115.2KBIT 2.5MM 8-SMD RoHS:是 類別:傳感器，轉換器 >> IrDA 收發器模塊 系列:- 產品變化通告:Product Discontinuation 30/Sept/2009 產品目錄繪圖:GP2W Series 標準包裝:1 系列:* 數據速率:115.2kbs（SIR） 電源電壓:2.4 V ~ 3.6 V 無效電流，標準值@ 25° C:70µA 通信距離，低功率:20cm 方向:側視圖 工作溫度:-40°C ~ 85°C 尺寸:8.3mm x 2.1mm x 1.7mm 標準:IrPHY 1.4 關機:* 包裝:Digi-Reel® 其它名稱:425-2614-6 |
| TFDU4300-TR1 | 功能描述:紅外收發器 SIR 115.2 kbits/s 2.4-5.5V Op Voltage RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
| TFDU4300-TR1 | 制造商:Vishay Semiconductors 功能描述:IrDA - Infrared Transceiver |
發布緊急采購，3分鐘左右您將得到回復。