參數資料
型號: TFA9812HN
廠商: NXP SEMICONDUCTORS
元件分類: 音頻/視頻放大
英文描述: 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48
封裝: 7 X 7 MM, 0.85 MM HEIGHT, PLASTIC, MO-220, SOT619-8, HVQFN-48
文件頁數: 6/66頁
文件大小: 386K
代理商: TFA9812HN
TFA9812_2
NXP B.V. 2009. All rights reserved.
Preliminary data sheet
Rev. 02 — 22 January 2009
14 of 66
NXP Semiconductors
TFA9812
BTL stereo Class-D audio amplier with I2S input
In I2C control mode communication is enabled after 4 ms. The preferred I2C settings can
be made within 66 ms before the PLL starts running. Finally, the output stages are
enabled and the audio level is increased via a demute sequence if mute has previously
been disabled.
Remark: In I2C mode soft mute is enabled by default. It can be disabled at any time while
I2C communication is valid. In order to prevent audio clicks volume control (default setting
is 0 dB) should be set before soft mute is disabled.
Remark: For a proper start-up in I2S master mode and I2C mode the following sequence
should be followed:
1. The I2S master setting should be set and keep the default sample rate setting active.
2. Next, another sample rate setting than the default one should be selected.
3. Finally, when the default sample rate is used the default sample rate setting should be
selected again.
8.3.2 Power-down
Figure 3 includes the power-down timing while Table 11 shows the pin control for enabling
power-down.
Putting the TFA9812 into power-down is equivalent to enabling Sleep mode
(see Section 8.2.2). This mode is entered immediately and no additional clock cycles are
required.
In order to prevent audible clicks, soft mute should be enabled at least Td(soft_mute)
seconds before enabling Sleep mode.
The specied low current and power conditions in Table 1 are valid within 10
s after
enabling Sleep mode.
8.4 Digital audio data input
8.4.1 Digital audio data format support
The TFA9812 supports a commonly used range of I2S and I2S-like digital audio data input
formats. These are listed in Table 12.
Table 11.
Power-up/power-down selection
Power-up pin
value
Description
0
Power-down (Sleep mode)
1
Power-up
Table 12.
Supported digital audio data formats
BCK frequency Interface format (MSB rst)
Supported in I2C
control mode
Supported in Legacy
control mode
32 fs
I2S up to 16-bit data
yes
32 fs
MSB-justied 16-bit data
yes
32 fs
LSB-justied 16-bit data
yes
48 fs
I2S up to 24-bit data
yes
48 fs
MSB-justied up to 24-bit data
yes
相關PDF資料
PDF描述
TFA9812HN/N1,518 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48
TFA9812HN/N1,557 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48
TFDS5500-TR3 TRANSMITTER/RECEIVER IC, DMA8
TFDT5500-TR3 TRANSMITTER/RECEIVER IC, SMA8
TFDU5100-TR3 TRANSMITTER/RECEIVER IC, SMA8
相關代理商/技術參數
參數描述
TFA9812HN/N1,518 功能描述:IC AMP AUDIO 15W STER D 48HVQFN RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機,2-通道(立體聲) 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C,麥克風,靜音,短路保護,音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP(2.09x2.09) 封裝/外殼:25-WFBGA,WLCSP 包裝:帶卷 (TR)
TFA9812HN/N1,557 功能描述:IC AMP AUDIO 15W STER D 48HVQFN RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機,2-通道(立體聲) 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C,麥克風,靜音,短路保護,音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP(2.09x2.09) 封裝/外殼:25-WFBGA,WLCSP 包裝:帶卷 (TR)
TFA9815 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Stereo full-bridge audio amplifier 2 x 17 W
TFA9815T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Stereo full-bridge audio amplifier 2 x 17 W
TFA9815T/N1 制造商:NXP Semiconductors 功能描述:Tube