- 您現在的位置：買賣IC網 > PDF目錄371184 > TEA6100 PDF資料下載
參數資料
| 型號： | TEA6100 |
| 文件頁數： | 6/27頁 |
| 文件大?。?/td> | 513K |
| 代理商： | TEA6100 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
August 1987
6
Philips Semiconductors
Product specification
FM/IF system and microcomputer-based
tuning interface
TEA6100
In the AM mode, the level information at pin 3 cannot be directly used owing to AM modulation on the output signal of
the level amplifier. This signal requires filtering, which is achieved by the following method:
the multiplexer is switched to a position which causes the signal to be applied to the attenuator
after attenuation the signal is fed to an amplifier (the resultant gain of attenuator and amplifier is unity), after
amplification the signal is filtered by an internal resistor and external capacitor
after filtering the signal is applied to ADC2 and is externally available
In AM mode pin 5 contains the level information.
The voltages on pin 3 and 5 are converted into two 3-bit digital words by the ADC, which can then be read out by the
I
2
C bus. The meaning of the 3- bit words is shown in Table 1.
Table 1
3-bit words
The FM modulated signal is converted into an audio signal by the symmetrical quadrature detector. The main advantage
of such a detector is that it requires few external components.
An FM signal requires good AM suppression, and as a result, the IF amplifiers must act as limiters. To achieve good
suppression on small input signals the IF amplifiers must have a high gain and thus a high sensitivity. High sensitivity is
an undesirable property when used in car radio applications, this problem is solved by having an externally adjustable
mute stage to control the overall sensitivity of the device.
The IF mute stage is controlled by the level amplifier (soft muting) and is only active in FM mode. If the input falls below
a predetermined level, the mute stage becomes active. To avoid the 'ON/OFF' effect of the audio signal due to
fluctuations of the input signal, the mute stage is activated rapidly but de-activated slowly. The mute stage is de-activated
slowly, via a current source and an external capacitor at pin 2, to avoid aggressive behaviour of the audio signal. It is
possible to adjust the '
3 dB limiting point' of the audio output via the level voltage due to the level signal being externally
adjustable. If hard muting is required then pin 2 must be switched to ground.
The 8-bit counter allows accurate stop information to be obtained, because exact tuning is achieved when the measured
frequency is equal to the centre frequency of the IF filter.
To measure the input frequency, the number of pulses which occur in a defined time must be counted. This defined time
is refered to as 'window'. A wide window indicates a long measuring time and therefore a high accuracy. The counter
resolution is defined as Hertz per count. Due to the TEA6100 having to measure the IF frequencies of AM and FM, the
counter resolution must be adjustable (different channel spacing). The counter resolution depends on the setting of
dividers 1 (N1), divider 2 (N2) and the reference frequency (F
ref
). The divider ratios of N1 and N2 are controlled by
software (see section PROGRAMMING INFORMATION). In Table 3 the window and counter resolution has been
calculated for a reference frequency of 40 kHz. The accuracy is controlled by bit 7 of the input word. Although the
resolution is the same for bit 7 = logic 0 and bit 7 = logic 1, the width of the window doubles when bit 7 = logic 1.
bit 7 = 0, accuracy =
±
counter resolution
bit 7 = 1, accuracy =
±
1
2
counter resolution
WORD
POSITION
FM
AM
1
2
multipath
level
level without modulation
level with modulation
相關PDF資料 |
PDF描述 |
|---|---|
| TEA6849H | New In Car Entertainment car radio tuner IC with Precision Adjacent Channel Suppression |
| TEA6886 | Up-level Car radio Analog Signal Processor CASP |
| TEA6886HL | Up-level Car radio Analog Signal Processor CASP |
| TEA8172 | TV Vertical Deflection Output Amplifier |
| TES225ZG-A | Very High Efficiency |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TEA6101 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Antenna diversity circuit |
| TEA6101T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Antenna diversity circuit |
| TEA6101T/N2,112 | 功能描述:射頻無線雜項 ANTENNA DIVERSITY RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| TEA6101T/N2,118 | 功能描述:射頻無線雜項 TUNING RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| TEA6101T/N3 | 功能描述:射頻無線雜項 ANTENNA SWITCH IC RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。