參數資料
型號: TEA2260
廠商: STMICROELECTRONICS
元件分類: 穩壓器
英文描述: 2.5 A SWITCHING CONTROLLER, 100 kHz SWITCHING FREQ-MAX, PDIP16
封裝: BATWING, PLASTIC, DIP-16
文件頁數: 11/11頁
文件大?。?/td> 127K
代理商: TEA2260
Obsolete
Product(s)
- Obsolete
Product(s)
TEA2261/0
9/11
SECURITY FUNCTIONS OF THE TEA2261 (see flowchart below)
Undervoltage Detection. This protection works in
association with the starting device “VCC switch”
(see paragraph Starting-mode - stand-by mode). If
VCC is lower than VCCstop (typically 7.4V) output
pulses are inhibited, in order to avoid wrong oper-
ation of the power supply or bad power transistor
drive.
Overvoltage Detection. If VCC exceeds VCCmax
(typically 15.7V) output pulses are inhibited and
the external capacitor C2 is charged as long as
VCC is higher than VCC stop. Restarting of the
power supply is obtained by reducing VCC below
VCCstop except if the voltage across C2 reaches
VC2 (typically 2.55V) (refer to “Restart of the power
supply” paragraph).In this last case, the circuit is
definitively stopped.
Current Limitation of the Power Transistor. The
current is measured by a shunt resistor. A double
threshold system is used:
– When the first threshold (VIM1) is reached, the
conduction of the power transistor is stopped un-
til the end of the period: a new conduction signal
is needed to obtain conduction again.
– Furthermore as long as the first threshold is
reached (it means during several periods), an ex-
ternal capacitor C2 is charged. When the voltage
across the capacitor reaches VC2 (typically
2.55V) the output is inhibited. This is called the
“repetitive overload protection”. If the overload
disappears before VC2 is reached, C2 is dis-
charged, so transient overloads are tolerated.
– Second current limitation threshold (VIM2). When
this threshold is reached the output of the circuit
is immediately inhibited. This protection is helpful
in case of hard overload for example to avoid the
magnetization of the transformer.
Restart of the Power Supply. After stopping due
to VIM2, VCCMax or VCCstop triggering, restart of
the power supply can be obtained by the normal
operating of the “VCC switch” VCC switch sequency
from VCCstop to VCCstart. After stopping due to
VC2 threshold reaching, the circuit is definitively
stopped. In this case it is necessary to reduce VCC
below approximately 5V to reset the circuit. From a
practical point of view, it means that the power
supply has to be temporarily disconnected from
any power source to get the restart.
Figure 6. Security Flowchart (TEA2260)
22
61-
76
.eps
S.M.P.S.
starting
First
threshold reached
VIM1
2
V
< 2.6V
C2
CC
V
max
reached
2
Normal operating
C discharged
Definitive
stopping
N
Y
N
Y
N
Y
Pulse by pulse current
limiting C charged
2
C charged
S.M.P.S. stopped
V
< 2.6V
C2
Y
Reset C
discharged
2
N
Second
threshold reached
VIM2
相關PDF資料
PDF描述
TEA3718DP STEPPER MOTOR CONTROLLER, 1.5 A, PDIP16
TEA3718SP STEPPER MOTOR CONTROLLER, 1.5 A, PZFM15
TEA5040S SPECIALTY CONSUMER CIRCUIT, PDIP42
TEA5040 SPECIALTY CONSUMER CIRCUIT, PDIP40
TEA5551TD AM, AUDIO SINGLE CHIP RECEIVER, PDSO16
相關代理商/技術參數
參數描述
TEA2261 功能描述:視頻 IC SMPS Controller RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
TEA2261_03 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SWITCH MODE POWER SUPPLY CONTROLLER
TEA2262 功能描述:電流型 PWM 控制器 SMPS Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
TEA2R2M1CTR-0512P 功能描述:鋁質電解電容器 - 帶引線 16V 2.2uF 20% RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk
TEA2R2M1HBK-0512P 功能描述:鋁質電解電容器 - 帶引線 50V 2.2uF 20% RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk