- 您現在的位置：買賣IC網 > PDF目錄383943 > TEA1533T (NXP SEMICONDUCTORS) GreenChipTMII SMPS control IC PDF資料下載
參數資料
| 型號： | TEA1533T |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 穩壓器 |
| 英文描述： | GreenChipTMII SMPS control IC |
| 中文描述： | 2 A SWITCHING CONTROLLER, 205 kHz SWITCHING FREQ-MAX, PDSO14 |
| 封裝： | 3.90 MM, PLASTIC, SOT-108-1, SO-14 |
| 文件頁數： | 19/24頁 |
| 文件大?。?/td> | 117K |
| 代理商： | TEA1533T |
2002 Aug 23
19
Philips Semiconductors
Product specification
GreenChip
TM
II SMPS control IC
TEA1533P; TEA1533AP
SOLDERING
Introduction to soldering through-hole mount
packages
This text gives a brief insight to wave, dip and manual
soldering.Amorein-depth account ofsoldering ICscanbe
found in our “Data Handbook IC26; Integrated Circuit
Packages”(document order number 9398 652 90011).
Wave soldering is the preferred method for mounting of
through-hole mount IC packages on a printed-circuit
board.
Soldering by dipping or by solder wave
The maximum permissible temperature of the solder is
260
°
C; solder at this temperature must not be in contact
with the joints for more than 5 seconds.
Thetotalcontacttimeofsuccessivesolderwavesmustnot
exceed 5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
stg(max)
). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Manual soldering
Apply the soldering iron (24 V or less) to the lead(s) of the
package, either below the seating plane or not more than
2 mm above it. If the temperature of the soldering iron bit
is less than 300
°
C it may remain in contact for up to
10 seconds. If the bit temperature is between
300 and 400
°
C, contact may be up to 5 seconds.
Suitability of through-hole mount IC packages for dipping and wave soldering methods
Note
1.
For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board.
PACKAGE
SOLDERING METHOD
DIPPING
WAVE
DBS, DIP, HDIP, SDIP, SIL
suitable
suitable
(1)
相關PDF資料 |
PDF描述 |
|---|---|
| TEA1541 | SMPS control IC with synchronization function |
| TEA1541P | SMPS control IC with synchronization function |
| TEA1552 | GreenChipII SMPS control IC |
| TEA5594 | AM/FM radio receiver circuit |
| TEA5710TD-T | AM/FM Receiver Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TEA1533T/N1,118 | 功能描述:電壓模式 PWM 控制器 GREENCHIP II SMPS CONTROL IC RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| TEA1533T/N1,518 | 功能描述:電壓模式 PWM 控制器 SMPS LOW STANDBY RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| TEA1533TD-T | 功能描述:電壓模式 PWM 控制器 SMPS LOW STANDBY GREENCHIP RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| TEA1541 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SMPS control IC with synchronization function |
| TEA1541P | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SMPS control IC with synchronization function |
發布緊急采購，3分鐘左右您將得到回復。