參數資料
型號： TE28F008C3T110
廠商： Intel Corp.
英文描述： 3 VOLT ADVANCED+ BOOT BLOCK 8-, 16-, 32-MBIT FLASH MEMORY FAMILY
中文描述： 3伏高級啟動塊8 - ，16 - ，32 - Mbit閃存家庭
文件頁數： 12/59頁
文件大小： 384K
代理商： TE28F008C3T110
3 VOLT ADVANCED+ BOOT BLOCK
E
12
PRODUCT PREVIEW
3.1.4
RESET
From read mode, RP# at V
IL
for time t
PLPH
deselects the memory, places output drivers in a
high-mpedance state, and turns off all internal
circuits. After return from reset, a time t
PHQV
is
required until the initial read access outputs are
valid. A delay (t
PHWL
or t
PHEL
) is required after
return from reset before a write can be initiated.
After this wake-up interval, normal operation is
restored. The CUI resets to read array mode, and
the status register is set to 80H. This case is shown
in Figure 11A.
If RP# is taken low for time t
PLPH
during a program
or erase operation, the operation will be aborted
and the memory contents at the aborted location
(for a program) or block (for an erase) are no longer
valid, since the data may be partially erased or
written. The abort process goes through the
following sequence: When RP# goes low, the
device shuts down the operation in progress, a
process which takes time t
PLRH
to complete. After
this time t
PLRH
, the part will either reset to read
array mode (if RP# has gone high during t
PLRH
,
Figure 11B) or enter reset mode (if RP# is still logic
low after t
PLRH
, Figure 11C). In both cases, after
returning from an aborted operation, the relevant
time t
PHQV
or t
PHWL
/t
PHEL
must be waited before a
read or write operation is initiated, as discussed in
the previous paragraph. However, in this case,
these delays are referenced to the end of t
PLRH
rather than when RP# goes high.
As with any automated device, it is important to
assert RP# during system reset. When the system
comes out of reset, processor expects to read from
the flash memory. Automated flash memories
provide status information when read during
program or block erase operations. If a CPU reset
occurs with no flash memory reset, proper CPU
initialization may not occur because the flash
memory may be providing status information
instead of array data. Intel’s flash memories allow
proper CPU initialization following a system reset
through the use of the RP# input. In this application,
RP# is controlled by the same RESET# signal that
resets the system CPU.
3.1.5
WRITE
A write takes place when both CE# and WE# are
low and OE# is high. Commands are written to the
Command User Interface (CUI) using standard
microprocessor write timings to control flash
operations. The CUI does not occupy an
addressable memory location. The address and
data buses are latched on the rising edge of the
second WE# or CE# pulse, whichever occurs first.
Figure 10 illustrates a program and erase operation.
The available commands are shown in Table 6, and
Appendix A provides detailed information on
moving between the different modes of operation
using CUI commands.
There are two commands that modify array data:
Program (40H) and Erase (20H). Writing either of
these commands to the internal Command User
Interface (CUI) initiates a sequence of internally
-
timed functions that culminate in the completion of
the requested task (unless that operation is aborted
by either RP# being driven to V
IL
for t
PLRH
or an
appropriate suspend command).
3.2
Modes of Operation
The flash memory has four read modes and two
write modes. The read modes are read array, read
configuration, read status, and read query. The
write modes are program and block erase. Three
additional modes (erase suspend to program, erase
suspend to read and program suspend to read) are
available only during suspended operations. These
modes
are
reached
summarized in Tables 5 and 6. A comprehensive
chart showing the state transitions is in Appendix A.
using
the
commands
3.2.1
READ ARRAY
When RP# transitions from V
IL
(reset) to V
IH
, the
device defaults to read array mode and will respond
to the read control inputs (CE#, address inputs, and
OE#) without any additional CUI commands.
When the device is in read array mode, four control
signals control data output:
WE# must be logic high (V
IH
)
CE# must be logic low (V
IL
)
OE# must be logic low (V
IL
)
RP# must be logic high (V
IH
)
In addition, the address of the desired location must
be applied to the address pins. If the device is not
in read array mode, as would be the case after a
program or erase operation, the Read Array
command (FFH) must be written to the CUI before
array reads can take place.
相關PDF資料
PDF描述
TE28F320C3T110 3 VOLT ADVANCED+ BOOT BLOCK 8-, 16-, 32-MBIT FLASH MEMORY FAMILY
TE28F160C3T110 3 VOLT ADVANCED+ BOOT BLOCK 8-, 16-, 32-MBIT FLASH MEMORY FAMILY
TE28F800C3T110 3 VOLT ADVANCED+ BOOT BLOCK 8-, 16-, 32-MBIT FLASH MEMORY FAMILY
TE28F320S3-100 16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
TE28F160S3-100 16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
相關代理商/技術參數
參數描述
TE28F008C3T90 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3 VOLT ADVANCED+ BOOT BLOCK 8-, 16-, 32-MBIT FLASH MEMORY FAMILY
TE28F008S3150 制造商:Rochester Electronics LLC 功能描述:- Bulk
TE28F008S3-150 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:BYTE-WIDE SMART 3 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT
TE28F008S5-100 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4, 8, AND 16 MBIT
TE28F008SA-100 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:8-MBIT (1-MBIT x 8) FlashFileTM MEMORY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*