參數資料
型號： TDF8554J/N4
廠商： NXP SEMICONDUCTORS
元件分類： 音頻／視頻放大
英文描述： 44 W, 4 CHANNEL, AUDIO AMPLIFIER, PZFM37
封裝： PLASTIC, SOT725-1, 37 PIN
文件頁數： 5/56頁
文件大?。?/td> 597K
代理商： TDF8554J/N4
TDF8554J
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 1 — 31 August 2011
13 of 56
NXP Semiconductors
TDF8554J
4
45 W power amplifier with multiple voltage regulator
7.4.5 Thermal pre-warning and thermal protection
If the average junction temperature reaches one of the adjustable levels set via the
I2C-bus, selected with IB3[D4], pre-warning is activated resulting in pin DIAG LOW (if
selected) and can be read via the I2C-bus. The default setting for the thermal pre-warning
is IB3[D4] = 0, setting the warning level at Tj(AV)(pwarn) = 160 C.
If the temperature increases further, the temperature-controlled gain reduction is activated
for all four channels to reduce the output power; see Figure 7. If this does not reduce the
average junction temperature, all four channels are switched off at the absolute maximum
temperature Toff.
7.5 Diagnostics
Diagnostic information can be read via the I2C-bus, but can also be made available at
pin DIAG. This information is seen at pin DIAG as a logical OR. In case of a failure,
pin DIAG remains LOW and the microcontroller can read the failure information via the
I2C-bus; pin DIAG can be used as a microcontroller interrupt to minimize I2C-bus traffic.
When the failure is removed, pin DIAG is released.
If the clip information is not needed, it can be removed from pin DIAG, enabling pin DIAG
to be used as an interrupt input for the microprocessor.
Fig 7.
Temperature controlled amplifier gain
001aam696
10
20
30
G
(dB)
0
Tj (°C)
140
190
180
160
170
150
Table 4.
Diagnostic information on pin DIAG
Diagnostic information
Pin DIAG
Power-on reset
after power-on reset; pin DIAG will remain LOW until amplifier
has started
Low battery
yes
Clip detection
can be enabled if IB4[D2] = 0
Temperature pre-warning
yes
Short-circuit outputs to battery,
ground or across the load
yes
Speaker fault detection
yes
Offset detection
no
Load detection
no
相關PDF資料
PDF描述
TDF8555J/N1 44 W, 4 CHANNEL, AUDIO AMPLIFIER, PZFM37
TDF8599TD 70 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO36
TDF8599TH 70 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO36
TDF8704T/4-T 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO24
TDF8704T/5-T 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO24
相關代理商/技術參數
參數描述
TDF8590TH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2 X 80 W SE (4 OHM) or 1 X 160 W BTL (8 OHM) class-D amplifier
TDF8590TH/N1,118 功能描述:音頻放大器 AMPLIFIER CLASS D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TDF8590TH/N1S,118 功能描述:音頻放大器 4/8 OHM CLASS D AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TDF8590TH/N1-T 功能描述:音頻放大器 AMPLIFIER CLASS D RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TDF8590TH/N1TJ 制造商:NXP Semiconductors 功能描述:- Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*