- 您現在的位置：買賣IC網 > PDF目錄368631 > TDA8946J (NXP SEMICONDUCTORS) 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier(2 x 15W立體聲BTL音頻放大器) PDF資料下載
參數資料
| 型號： | TDA8946J |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier(2 x 15W立體聲BTL音頻放大器) |
| 中文描述： | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PZIP17 |
| 封裝： | PLASTIC, DIL-BENT-SIL, 17 PIN |
| 文件頁數： | 15/23頁 |
| 文件大?。?/td> | 393K |
| 代理商： | TDA8946J |
Philips Semiconductors
TDA8946J
2 x 15 W stereo BTL audio amplifier
Product specification
Rev. 02 — 14 March 2000
15 of 23
9397 750 06863
Philips Electronics N.V. 2000. All rights reserved.
14.1.2
Power supply decoupling
Proper supply bypassing is critical for low-noise performance and high supply voltage
ripple rejection. The respective capacitor locations should be as close as possible to
the device and grounded to the power ground. Proper power supply decoupling also
prevents oscillations.
For suppressing higher frequency transients (spikes) on the supply line a capacitor
with low ESR – typical 100 nF – has to be placed as close as possible to the device.
For suppressing lower frequency noise and ripple signals, a large electrolytic
capacitor – e.g. 1000
μ
F or greater – must be placed close to the device.
The bypass capacitor on the SVR pin reduces the noise and ripple on the midrail
voltage. For good THD and noise performance a low ESR capacitor is recommended.
Fig 15. Printed-circuit board layout (single-sided); components view.
idth
MGU069
ON
MUTE
220 nF
100 nF
1.5 nF
1000
F
10
μ
F
220 nF
1
17
+
IN2
IN2
+
IN1
IN1
+
OUT1
OUT1
+
OUT2
OUT2
+
VCC
GND
54 mm
56 mm
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8946 | 2 x 15 W stereo Bridge Tied Load BTL audio amplifier |
| TDA9160 | PAL/NTSC/SECAM decoder/sync processor(PAL/NTSC/SECAM譯碼器/ 同步處理器) |
| TDA935X | TV signal processor-Teletext decoder with embedded m-Controller |
| TDA936X | TV signal processor-Teletext decoder with embedded m-Controller |
| TDA938X | TV signal processor-Teletext decoder with embedded m-Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8946J/N1,112 | 功能描述:音頻放大器 AUDIO AMP 2X15W RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8947J | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4-channel audio amplifier (SE: 1 W to 25 W; BTL: 4 W to 50 W) |
| TDA8947J/N3,112 | 功能描述:音頻放大器 3/4 CHANNEL AUD AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8948J | 功能描述:音頻放大器 4X10W MPA RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8948J/N1,112 | 功能描述:音頻放大器 4X10W MPA RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。