- 您現在的位置：買賣IC網 > PDF目錄98204 > TDA8942P/N1,112 (NXP SEMICONDUCTORS) 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP16 PDF資料下載
參數資料
| 型號： | TDA8942P/N1,112 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP16 |
| 封裝： | 0.300 INCH, PLASTIC, SOT-38-1, MO-001, DIP-16 |
| 文件頁數： | 20/22頁 |
| 文件大小： | 394K |
| 代理商： | TDA8942P/N1,112 |
Philips Semiconductors
TDA8942P
2 x 1.5 W (3 W music power) stereo BTL audio amplier
Product data
Rev. 03 — 02 September 2003
7 of 22
9397 750 11707
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
Standby — In this mode the current consumption is very low and the outputs are
oating. The device is in standby mode when (VCC 0.5 V) < VMODE <VCC, or when
the MODE pin is left oating (high impedance). The power consumption of the
TDA8942P will be reduced to < 0.18 mW.
Mute — In this mode the amplier is DC-biased but not operational (no audio output);
the DC level of the input and output pins remain on half the supply voltage. This
allows the input coupling and Supply Voltage Ripple Rejection (SVRR) capacitors to
be charged to avoid pop-noise. The device is in mute mode when
3V<VMODE <(VCC 1.5 V).
Operating — In this mode the amplier is operating normally. The operating mode is
activated at VMODE < 0.5 V.
8.3.1
Switch-on and switch-off
To avoid audible plops during supply voltage switch-on or switch-off, the device is set
to standby mode before the supply voltage is applied (switch-on) or removed
(switch-off).
The switch-on and switch-off time can be inuenced by an RC-circuit on the MODE
pin. Rapid on/off switching of the device or the MODE pin may cause ‘click- and
pop-noise’. This can be prevented by proper timing of the RC-circuit on the MODE
pin.
8.4 Supply voltage ripple rejection
The supply voltage ripple rejection (SVRR) is measured with an electrolytic capacitor
of 10
F on pin SVR at a bandwidth of 10 Hz to 80 kHz. Figure 13 illustrates the
SVRR as function of the frequency. A larger capacitor value on the SVR pin improves
the ripple rejection behavior at the lower frequencies.
8.5 Built-in protection circuits
The TDA8942P contains two types of protection circuits, i.e. short-circuit and thermal
shutdown.
8.5.1
Short-circuit protection
Short-circuit to ground or supply line — This is detected by a so-called ‘missing
current’ detection circuit which measures the current in the positive supply line and
the current in the ground line. A difference between both currents larger than 0.4 A,
switches the power stage to standby mode (high impedance).
Short-circuit across the load — This is detected by an absolute-current
measurement. An absolute-current larger than 2 A, switches the power stage to
standby mode (high impedance).
8.5.2
Thermal shutdown protection
The junction temperature is measured by a temperature sensor; at a junction
temperature of approximately 150
°C this detection circuit switches the power stage
to standby mode (high impedance).
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8944AJ | 7 W, 2 CHANNEL, AUDIO AMPLIFIER, PZIP17 |
| TDA8946AJ | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PZIP17 |
| TDA9103 | HORIZ/VERT DEFLECTION IC, PDIP42 |
| TDA9105 | HORIZ/VERT DEFLECTION IC, PDIP42 |
| TDA9109/SN | HORIZ/VERT DEFLECTION IC, PDIP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8943 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:6 W mono Bridge Tied Load BTL audio amplifier |
| TDA8943SF | 制造商:PHILPS 功能描述: |
| TDA8943SF/N1,112 | 功能描述:音頻放大器 6W MONO BTL PWR AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8943SF/N1.112 | 制造商:NXP Semiconductors 功能描述:AMP AUDIO POWER SINGLE 8943 SIL-9 |
| TDA8944 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2 x 7 W stereo Bridge Tied Load BTL audio amplifier |
發布緊急采購，3分鐘左右您將得到回復。