- 您現在的位置：買賣IC網 > PDF目錄368630 > TDA8768AH (NXP Semiconductors N.V.) 12-bit, 70 Msps Analog-to-Digital Converter (ADC) PDF資料下載
參數資料
| 型號： | TDA8768AH |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 12-bit, 70 Msps Analog-to-Digital Converter (ADC) |
| 中文描述： | 12位，70 Msps的模擬到數字轉換器（ADC） |
| 文件頁數： | 28/32頁 |
| 文件大?。?/td> | 915K |
| 代理商： | TDA8768AH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁
Philips Semiconductors
TDA8768A
12-bit, 70 Msps Analog-to-Digital Converter (ADC)
Product data
Rev. 02 — 03 July 2002
28 of 32
9397 750 09656
Koninklijke Philips Electronics N.V. 2002. All rights reserved.
14. Handling information
Inputs and outputs are protected against electrostatic discharge in normal handling.
However, to be completely safe, it is desirable to take normal precautions appropriate
to handling integrated circuits.
15. Soldering
15.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is recommended.
15.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 250
°
C. The top-surface
temperature of the packages should preferable be kept below 220
°
C for thick/large
packages, and below 235
°
C small/thin packages.
15.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8768AH4 | 12-bit, 70 Msps Analog-to-Digital Converter (ADC) |
| TDA8768AH5 | 12-bit, 70 Msps Analog-to-Digital Converter (ADC) |
| TDA8768AH7 | 12-bit, 70 Msps Analog-to-Digital Converter (ADC) |
| TDA8768 | 12-bit high-speed Analog-to-Digital Converter ADC |
| TDA8768H | 12-bit high-speed Analog-to-Digital Converter ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8768AH4 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:12-bit, 70 Msps Analog-to-Digital Converter (ADC) |
| TDA8768AH5 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:12-bit, 70 Msps Analog-to-Digital Converter (ADC) |
| TDA8768AH7 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:12-bit, 70 Msps Analog-to-Digital Converter (ADC) |
| TDA8768H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:12-bit high-speed Analog-to-Digital Converter ADC |
| TDA8768H/4 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:12-bit high-speed Analog-to-Digital Converter ADC |
發布緊急采購，3分鐘左右您將得到回復。