- 您現在的位置：買賣IC網 > PDF目錄368629 > TDA8561 (NXP Semiconductors N.V.) 2 x 24 W BTL or 4 x 12 W single-ended car radio power amplifier PDF資料下載
參數資料
| 型號： | TDA8561 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 2 x 24 W BTL or 4 x 12 W single-ended car radio power amplifier |
| 中文描述： | 2 × 24糯橋接或4 x 12瓦的單端汽車無線電功率放大器 |
| 文件頁數： | 5/24頁 |
| 文件大?。?/td> | 117K |
| 代理商： | TDA8561 |
1999 Jun 30
5
Philips Semiconductors
Product specification
2
×
24 W BTL or 4
×
12 W single-ended
car radio power amplifier
TDA8561Q
FUNCTIONAL DESCRIPTION
The TDA8561Q contains four identical amplifiers and can
be used for Single-Ended (SE) or Bridge-Tied Load (BTL)
applications. The gain of each amplifier is fixed at 20 dB
(26 dB in BTL). Special features of the device are:
Mode select switch (pin 14)
Low standby current (<100
μ
A)
Low switching current (low cost supply switch)
Mute facility.
To avoid switch-on plops, it is advised to keep the amplifier
in the mute mode during
≥
100 ms (charging of the input
capacitors at pins 1, 3, 15 and 17). This can be achieved
by:
Microcontroller control
External timing circuit (see Fig.11).
Diagnostic output (pin 16)
D
YNAMIC
D
ISTORTION
D
ETECTOR
(DDD)
At the onset of clipping of one or more output stages, the
dynamic distortion detector becomes active and pin 16
goes LOW. This information can be used to drive a sound
processor or DC volume control to attenuate the input
signal and thus limit the distortion. The output level of
pin 16 is independent of the number of channels that are
clipping (see Figs 3 and 4).
S
HORT
-
CIRCUIT PROTECTION
When a short-circuit occurs at one or more outputs to
ground or to the supply voltage, the output stages are
switched off until the short-circuit is removed and the
device is switched on again, with a delay of approximately
20 ms, after removal of the short-circuit. During this
short-circuit condition, pin 16 is continuously LOW.
When a short-circuit across the load of one or both
channels occurs the output stages are switched off for
approximately 20 ms. After that time it is checked during
approximately 50
μ
s to see whether the short-circuit is still
present. Due to this duty cycle of 50
μ
s/20 ms the average
current consumption during this short-circuit condition is
very low (approximately 40 mA).
During this short-circuit condition, pin 16 is LOW for 20 ms
and HIGH for 50
μ
s (see Fig.5).
The power dissipation in any short-circuit condition is very
low.
Fig.3
Distortion detector waveform; BTL
application.
handbook, halfpage
V
0
VP
VO
0
t
MGA705
16
Fig.4
Distortion detector waveform; single-ended
application.
handbook, halfpage
0
VP
VO
t
0
MGA706
V16
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8563Q | 2 x 40 W/2 ohm stereo BTL car radio power amplifier with diagnostic facility |
| TDA8564Q | 2 x 24 W BTL or 4 x 12 W single-ended car radio power amplifier |
| TDA8567 | 4 x 25 W BTL quad car radio power amplifier |
| TDA8568Q | 4x25 W BTL quad car radio power amplifier(4x25 W BTL雙路車載電臺功率放大器) |
| TDA8568 | 4 x 25 W BTL quad car radio power amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8561Q | 制造商:NXP Semiconductors 功能描述:Audio Amplifier Circuit, Quad, 17 Pin, Plastic, ZIP |
| TDA8561Q/N2 | 制造商:PHILIPS-SEMI 功能描述: |
| TDA8561Q/N3C | 功能描述:音頻放大器 2X24 W BTL OR 4X12 W RADIO AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8561Q/N3C,112 | 功能描述:音頻放大器 2X24 W BTL OR 4X12 W RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8561Q/N3S,112 | 功能描述:音頻放大器 SNGL ENDED CAR RADIO POWER AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。