參數資料
型號: TDA8380
廠商: NXP SEMICONDUCTORS
元件分類: 穩壓器
英文描述: Control circuit for switched mode power supplies
中文描述: 2.5 A SWITCHING CONTROLLER, 100 kHz SWITCHING FREQ-MAX, PDIP16
封裝: 0.300 INCH, PLASTIC, DIP-16
文件頁數: 10/20頁
文件大?。?/td> 158K
代理商: TDA8380
November 1993
10
Philips Semiconductors
Product specification
Control circuit for switched mode power supplies
TDA8380A
Demagnetization sense circuit
To enable the SMPS to be kept in the non-continuous mode, an input is available which delays switch-on of the
high-voltage transistor until the transformer currents have decayed to zero. This is an effective way of avoiding
transformer saturation. The waveforms illustrated by Fig.9 show demagnetization with respect to the application diagram
of Fig.13.
As long as the voltage of the take-over (auxiliary) winding (also used for supplying the device) is above 0.6 V (V
3
) the
output will be prevented from switching on.
Over-current protection
The over-current protection circuit (pin 13) senses the voltage across resistor R
s
(see Fig.13), which reflects the primary
current. This generated voltage is negative-going as the emitter of the high-voltage power transistor is grounded (this
circuit arrangement provides the IC with the best safeguard against a possible collector-emitter short-circuit in the power
transistor). At pin 13, the negative voltage signal is shifted to a positive level by a voltage across resistor R
13
. This voltage
is set by the reference current at pin 13 and is defined by resistor R
6
at the I
ref
input (pin 6) and = 1/6
×
V
ref
/R
6
.
Therefore V
shift
(V
R 13
) = V
ref
/6
×
R
13
/R
6
or nominal 0.416
×
R
13
/R
6
(V).
The positive current monitor voltage at pin 13 is compared with two voltage levels: the first level = 0.2 V and the second
level = 0 V (see Fig.10).
The first trip level only switches off the high-voltage transistor for a cycle and puts the SMPS in a continuous
cycle-by-cycle current protection mode.
The second trip level is only activated when the primary current rise is very fast which can occur during a short-circuited
output. In this mode the high-voltage transistor is quickly switched off and the slow-start procedure is activated.
The difference between the first and second primary current peak levels is set by R
s
:
I
2
I
1
= 0.2/R
s
.
The absolute peak values are set by R
6
and R
13
:
I
2
×
R
s
= 0.416
×
R
13
/R
6
or
I
1
×
R
s
= (0.416
×
R
13
/R
6
)
0.2
Fig.9 Demagnetization function.
相關PDF資料
PDF描述
TDA8380A Control circuit for switched mode power supplies
TDA8385 Control circuit for a Self-Oscillating Power Supply SOPS
TDA8395 SECAM decoder
TDA8440 Switch for CTV receivers
TDA8442 I2C-bus interface for colour decoders
相關代理商/技術參數
參數描述
TDA8380A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Control circuit for switched mode power supplies
TDA8385 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Control circuit for a Self-Oscillating Power Supply SOPS
TDA8390 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:PAL DECODER AND RGB MATRIX
TDA8391 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:One-chip PAL decoder and RGB matrix
TDA8395 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SECAM decoder