- 您現在的位置：買賣IC網 > PDF目錄98194 > TDA7348D013TR (STMICROELECTRONICS) 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | TDA7348D013TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 |
| 封裝： | SOP-28 |
| 文件頁數： | 2/20頁 |
| 文件大小： | 218K |
| 代理商： | TDA7348D013TR |
I2C BUS interface
TDA7348
3
I2C BUS interface
Data transmission from microprocessor to the TDA7348 and vice-versa takes place through
the 2 wires of the I2C BUS interface, consisting of the two lines SDA and SCL (pull-up
resistors to the positive supply voltage must be externally connected).
3.1
Data validity
As shown in Figure 3., the data on the SDA line must be stable during the high period of the
clock. The HIGH and LOW state of the data line can only change when the clock signal on
the SCL line is LOW.
3.2
Start and stop conditions
As shown in Figure 4. a start condition is a HIGH to LOW transition of the SDA line while
SCL is HIGH. The stop condition is a LOW to HIGH transition of the SDA line while SCL is
HIGH.
A STOP conditions must be sent before each START condition.
3.3
Byte format
Every byte transferred to the SDA line must contain 8 bits. Each byte must be followed by an
acknowledge bit. The MSB is transferred first.
3.4
Acknowledge
The master (microprocessor) puts a resistive HIGH level on the SDA line during the
acknowledge clock pulse (see Figure 5.). The peripheral (audioprocessor) that
acknowledges has to pull-down (LOW) the SDA line during the acknowledge clock pulse, so
that the SDA line is stable LOW during this clock pulse.
The audioprocessor which has been addressed has to generate an acknowledge after the
reception of each byte, otherwise the SDA line remains at the HIGH level during the ninth
clock pulse time. In this case the master transmitter can generate the STOP information in
order to abort the transfer.
3.5
Transmission without acknowledgement
The microprocessor can use a simpler transmission, if it avoids detection of the
acknowledgement from the audio processor. It simply waits one clock pulse without
checking the slave acknowledgment, and sends the new data.
This approach of course is less protected from errors, increases the possibility of
interference, and decreases the immunity to noise.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA7348 | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDIP28 |
| TDA7350A | 11 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM11 |
| TDA7350 | 22 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM11 |
| TDA7370BV | 6.5 W, 4 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
| TDA7370B | 6.5 W, 4 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA7350 | 功能描述:音頻放大器 10W Stereo Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA7350A | 功能描述:音頻放大器 10W Stereo Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA7350A_05 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:22W BRIDGE-STEREO AMPLIFIER FOR CAR RADIO |
| TDA7360 | 功能描述:音頻放大器 22W Stereo Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA7360HS | 功能描述:音頻放大器 18V Op 28V DC 36W 50V Supply 5A Output RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。