- 您現在的位置：買賣IC網 > PDF目錄98193 > TDA7295S (STMICROELECTRONICS) 80 W, 1 CHANNEL, AUDIO AMPLIFIER, PZFM15 PDF資料下載
參數資料
| 型號： | TDA7295S |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 80 W, 1 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
| 封裝： | MULTIWATT-15 |
| 文件頁數： | 12/13頁 |
| 文件大?。?/td> | 391K |
| 代理商： | TDA7295S |
The TDA7295S is a monolithic MOS power ampli-
fier which can be operated at 76V supply voltage
(80V with no signal applied) while delivering out-
put currents up to
±6A.
This allows the use of this device as a very high
power amplifier (up to 80W as peak power with
T.H.D.=10 % and Rl = 4 Ohm); the only drawback
is the power dissipation, hardly manageable in
the above power range.
The typical junction-to-case thermal resistance of
the TDA7295S is 1
oC/W (max= 1.5 oC/W). To
avoid that, in worst case conditions, the chip tem-
perature exceedes 150
oC, the thermal resistance
of the heatsink must be 0.038
oC/W (@ max am-
bient temperature of 50
oC).
As the above value is pratically unreachable; a
high efficiency system is needed in those cases
where the continuous RMS output power is higher
than 50-60 W.
The TDA7295S was designed to work also in
higher efficiency way.
For this reason there are four power supply pins:
two intended for the signal part and two for the
power part.
T1 and T2 are two power transistors that only
operate when the output power reaches a certain
threshold (e.g. 20 W). If the output power in-
creases, these transistors are switched on during
the portion of the signal where more output volt-
age swing is needed, thus "bootstrapping" the
power supply pins (#13 and #15).
The current generators formed by T4, T7, zener
diodes Z1, Z2 and resistors R7,R8 define the
minimum drop across the power MOS transistors
of the TDA7295S. L1, L2, L3 and the snubbers
C9, R1 and C10, R2 stabilize the loops formed by
the "bootstrap" circuits and the output stage of the
TDA7295S.
By considering again a maximum average
output power (music signal) of 20W, in case
of the high efficiency application, the thermal
resistance value needed from the heatsink is
2.2
oC/W (Vs =±40V and Rl= 8 Ohm).
All components (TDA7295S and power tran-
sistors T1 and T2) can be placed on a
1.5
oC/W heatsink, with the power darlingtons
electrically insulated from the heatsink.
Since the total power dissipation is less than that
of a usual class AB amplifier, additional cost sav-
ings can be obtained while optimizing the power
supply, even with a high heatsink .
BRIDGE APPLICATION
Another application suggestion is the BRIDGE
configuration, where two TDA7295S are used.
In this application, the value of the load must not
be lower than 8 Ohm for dissipation and current
capability reasons.
A suitable field of application includes HI-FI/TV
subwoofers realizations.
The main advantages offered by this solution are:
- High power performances with limited supply
voltage level.
- Considerably high output power even with high
load values (i.e. 16 Ohm).
With Rl = 8 Ohm, VS =
±25V the maximum output
power obtainable is 150W (Music Power)
APPLICATION NOTE: (ref. fig. 7)
Modular Application (more Devices in Parallel)
The use of the modular application lets very high
power be delivered to very low impedance loads.
The modular application implies one device to act
as a master and the others as slaves.
The slave power stages are driven by the master
device and work in parallel all together, while the
input and the gain stages of the slave device are
disabled, the figure below shows the connections
required to configure two devices to work to-
gether.
The master chip connections are the same as
the normal single ones.
The outputs can be connected together with-
out the need of any ballast resistance.
The slave SGND pin must be tied to the nega-
tive supply.
The slave ST-BY pin must be connected to
ST-BY pin.
The bootstrap lines must be connected to-
gether and the bootstrap capacitor must be in-
creased: for N devices the boostrap capacitor
must be 22
F times N.
The slave Mute and IN-pins must be grounded.
THE BOOTSTRAP CAPACITOR
For compatibility purpose with the previous de-
vices of the family, the boostrap capacitor can be
connected both between the bootstrap pin (6) and
the output pin (14) or between the boostrap pin
(6) and the bootstrap loader pin (12).
TDA7295S
8/13
相關PDF資料 |
PDF描述 |
|---|---|
| TDA7295 | 80 W, 1 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
| TDA7296AV | 30 W, 1 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
| TDA7296SV | 60 W, 1 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
| TDA7296S | 60 W, 1 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
| TDA7296V | 60 W, 1 CHANNEL, AUDIO AMPLIFIER, PZFM15 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA7295SV | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:80V - 80W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY |
| TDA7295V | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:80V - 80W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY |
| TDA7296 | 功能描述:音頻放大器 60W Audio Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA-7296 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:70V - 60W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY |
| TDA7296_05 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:70V - 60W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY |
發布緊急采購，3分鐘左右您將得到回復。