- 您現在的位置：買賣IC網 > PDF目錄98192 > TDA6118JF/N2/S1 (NXP SEMICONDUCTORS) 1 CHANNEL, VIDEO AMPLIFIER, PSFM9 PDF資料下載
參數資料
| 型號： | TDA6118JF/N2/S1 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1 CHANNEL, VIDEO AMPLIFIER, PSFM9 |
| 封裝： | PLASTIC, SOT-111-1, DIL-BENT-SIL, 9 PIN |
| 文件頁數： | 5/15頁 |
| 文件大?。?/td> | 99K |
| 代理商： | TDA6118JF/N2/S1 |
2004 Aug 26
13
Philips Semiconductors
Product specication
Video output amplier
TDA6118JF
SOLDERING
Introduction to soldering through-hole mount
packages
This text gives a brief insight to wave, dip and manual
soldering. A more in-depth account of soldering ICs can be
found in our
“Data Handbook IC26; Integrated Circuit
Packages” (document order number 9398 652 90011).
Wave soldering is the preferred method for mounting of
through-hole mount IC packages on a printed-circuit
board.
Soldering by dipping or by solder wave
Driven by legislation and environmental forces the
worldwide use of lead-free solder pastes is increasing.
Typical dwell time of the leads in the wave ranges from
3 to 4 seconds at 250
°C or 265 °C, depending on solder
material applied, SnPb or Pb-free respectively.
The total contact time of successive solder waves must not
exceed 5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg(max)). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Manual soldering
Apply the soldering iron (24 V or less) to the lead(s) of the
package, either below the seating plane or not more than
2 mm above it. If the temperature of the soldering iron bit
is less than 300
°C it may remain in contact for up to
10 seconds. If the bit temperature is between
300 and 400
°C, contact may be up to 5 seconds.
Suitability of through-hole mount IC packages for dipping and wave soldering methods
Notes
1. For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board.
2. For PMFP packages hot bar soldering or manual soldering is suitable.
PACKAGE
SOLDERING METHOD
DIPPING
WAVE
CPGA, HCPGA
suitable
DBS, DIP, HDIP, RDBS, SDIP, SIL
suitable
suitable(1)
not suitable
相關PDF資料 |
PDF描述 |
|---|---|
| TDA6160-2X | FM, AUDIO DEMODULATOR, PDSO28 |
| TDA6170X | FM, AUDIO DEMODULATOR, PDSO28 |
| TDA6170X | FM, AUDIO DEMODULATOR, PDSO28 |
| TDA6190T | SPECIALTY CONSUMER CIRCUIT, PDSO16 |
| TDA6190X | SPECIALTY CONSUMER CIRCUIT, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA6120 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Video output amplifier |
| TDA6120Q | 制造商:Panasonic Industrial Company 功能描述:SUB ONLY P-C1AA00000326 IC SUBBING WITH C1AA00000326 |
| TDA6120Q/N2,112 | 功能描述:視頻放大器 VERY WIDEBAND RGB RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| TDA6130-5 | 制造商:Infineon Technologies AG 功能描述: |
| TDA6130-5X4 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:2-GHz MIXER |
發布緊急采購，3分鐘左右您將得到回復。