- 您現在的位置：買賣IC網 > PDF目錄383940 > TDA5149G (NXP SEMICONDUCTORS) 12 V Voice Coil Motor VCM driver and spindle motor pre-driver combination chip PDF資料下載
參數資料
| 型號： | TDA5149G |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 運動控制電子 |
| 英文描述： | 12 V Voice Coil Motor VCM driver and spindle motor pre-driver combination chip |
| 中文描述： | DISK DRIVE MOTOR CONTROLLER, 2.5 A, PQFP64 |
| 封裝： | 10 X 10 X 1.40 MM, PLASTIC, LQFP-64 |
| 文件頁數： | 24/28頁 |
| 文件大小： | 148K |
| 代理商： | TDA5149G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁
1996 May 06
24
Philips Semiconductors
Product specification
12 V Voice Coil Motor (VCM) driver and
spindle motor pre-driver combination chip
TDA5149G
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“IC Package Databook”
(order code 9398 652 90011).
Reflow soldering
Reflow soldering techniques are suitable for all LQFP
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
°
C.
Wave soldering
Wave soldering is
not
recommended for LQFP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
If wave soldering cannot be avoided, the following
conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The footprint must be at an angle of 45
°
to the board
direction and must incorporate solder thieves
downstream and at the side corners.
Even with these conditions, do not consider wave
soldering LQFP packages LQFP48 (SOT313-2),
LQFP64 (SOT314-2) or LQFP80 (SOT315-1).
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA5155 | Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
| TDA5155X | Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
| TDA5240 | Brushless DC motor drive circuit |
| TDA5240T | Brushless DC motor drive circuit |
| TDA5241 | Brushless DC motor drive circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA5150 | 功能描述:射頻發射器 WIRELESS CONTROLLER RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| TDA5150HTMA1 | 制造商:Infineon Technologies AG 功能描述:Multiband Transmitter 10-Pin TSSOP T/R 制造商:Infineon Technologies AG 功能描述:CONTROL - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC TX MULTI-CH/BAND 10-TSSOP |
| TDA5153 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
| TDA5153AG | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
| TDA5153BG | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
發布緊急采購，3分鐘左右您將得到回復。