- 您現在的位置：買賣IC網 > PDF目錄383940 > TDA5145T (NXP SEMICONDUCTORS) Brushless DC motor drive circuit PDF資料下載
參數資料
| 型號： | TDA5145T |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 運動控制電子 |
| 英文描述： | Brushless DC motor drive circuit |
| 中文描述： | BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, PDSO28 |
| 封裝： | PLASTIC, SOL-28 |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 249K |
| 代理商： | TDA5145T |
June 1994
11
Philips Semiconductors
Product specification
Brushless DC motor drive circuit
TDA5145
provided that will generate commutation pulses when no
zero-crossings in the motor voltage are available.
A timing function is incorporated into the device for internal
timing and for timing of the reverse rotation detection.
The TDA5145 also contains an uncommitted
transconductance amplifier (OTA) that can be used as a
control amplifier. The output is capable of directly driving
an external power transistor.
The TDA5145 is designed for systems with low current
consumption: use of I
2
L logic, adaptive base drive for the
output transistors (patented).
Adjustments
The system has been designed in such a way that the
tolerances of the application components are not critical.
However, the approximate values of the following
components must still be determined:
The start capacitor; this determines the frequency of the
start oscillator.
The two capacitors in the adaptive commutation delay
circuit; these are important in determining the optimum
moment for commutation, depending on the type and
loading of the motor.
The timing capacitor; this provides the system with its
timing signals.
T
HE START CAPACITOR
(CAP-ST)
This capacitor determines the frequency of the start
oscillator. It is charged and discharged, with a current of
2
μ
A, from 0.05 to 2.2 V and back to 0.05 V. The time
taken to complete one cycle is given by:
t
start
= (2.15
×
C) s (with C in
μ
F)
The start oscillator is reset by a commutation pulse and so
is only active when the system is in the start-up mode. A
pulse from the start oscillator will cause the outputs to
change to the next state (torque in the motor). If the
movement of the motor generates enough EMF the
TDA5145 will run the motor. If the amount of EMF
generated is insufficient, then the motor will move one step
only and will oscillate in its new position. The amplitude of
the oscillation must decrease sufficiently before the arrival
of the next start pulse, to prevent the pulse arriving during
the wrong phase of the oscillation. The oscillation of the
motor is given by:
where:
K
t
= torque constant (N.m/A)
I = current (A)
p = number of magnetic pole-pairs
J = inertia J (kg.m
2
)
Example: J = 72
×
10
6
kg.m
2
, K = 25
×
10
3
N.m/A, p = 6
and I = 0.5 A; this gives f
osc
= 5 Hz. If the damping is high
then a start frequency of 2 Hz can be chosen or
t = 500 ms, thus C = 0.5/2 = 0.25
μ
F (choose 220 nF).
T
HE ADAPTIVE COMMUTATION DELAY
(CAP-CD
AND
CAP-DC)
In this circuit capacitor CAP-CD is charged during one
commutation period, with an interruption of the charging
current during the diode pulse. During the next
commutation period this capacitor (CAP-CD) is discharged
at twice the charging current. The charging current is
8.1
μ
A and the discharging current 16.2
μ
A; the voltage
range is from 0.9 to 2.2 V. The voltage must stay within
this range at the lowest commutation frequency of
interest, f
C1
:
6
–
×
1.3
×
C1
(C in nF)
If the frequency is lower, then a constant commutation
delay after the zero-crossing is generated by the discharge
from 2.2 to 0.9 V at 16.2
μ
A;
maximum delay = (0.076
×
C) ms (with C in nF)
Example: nominal commutation frequency = 900 Hz and
the lowest usable frequency = 400 Hz; so:
(choose 18 nF)
The other capacitor, CAP-DC, is used to repeat the same
delay by charging and discharging with 15.5
μ
A. The same
value can be chosen as for CAP-CD. Figure 9 illustrates
typical voltage waveforms.
f
osc
2
π
----------J
I
×
p
×
------------K
=
C
8.1
10
6231
-f
=
=
CAP-CD
400
15.6
=
=
相關PDF資料 |
PDF描述 |
|---|---|
| TDA5145TS | Brushless DC motor drive circuit |
| TDA5147CH | 12 V Voice Coil Motor VCM driver and spindle motor drive combination chip |
| TDA5147K | 12 V Voice Coil Motor VCM driver and spindle motor drive combination chip |
| TDA5149 | 12 V Voice Coil Motor VCM driver and spindle motor pre-driver combination chip |
| TDA5149G | 12 V Voice Coil Motor VCM driver and spindle motor pre-driver combination chip |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA5145TS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Brushless DC motor drive circuit |
| TDA5145TS/C1,518 | 功能描述:BLDC MOTOR CONTROLLER RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| TDA5146T | 制造商:NXP Semiconductors 功能描述: |
| TDA5147CH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:12 V Voice Coil Motor VCM driver and spindle motor drive combination chip |
| TDA5147K | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:12 V Voice Coil Motor VCM driver and spindle motor drive combination chip |
發布緊急采購，3分鐘左右您將得到回復。