- 您現在的位置：買賣IC網 > PDF目錄384965 > TDA4714C (SIEMENS A G) IC for Switched-Mode Power Supplies (SMPS) PDF資料下載
參數資料
| 型號： | TDA4714C |
| 廠商： | SIEMENS A G |
| 元件分類： | 穩壓器 |
| 英文描述： | IC for Switched-Mode Power Supplies (SMPS) |
| 中文描述： | 0.07 A SWITCHING CONTROLLER, 100 kHz SWITCHING FREQ-MAX, PDIP14 |
| 封裝： | PLASTIC, DIP-14 |
| 文件頁數： | 5/17頁 |
| 文件大小： | 388K |
| 代理商： | TDA4714C |
TDA 4714 C
TDA 4716 C
Semiconductor Group
5
Pulse Turn-OFF Flipflop
The pulse turn-OFF flipflop enables the outputs at the start of each half cycle. If an error
signal from comparator K7 or a turn-off signal from K2 is present, the outputs will
immediately be switched off.
Comparator K3
Comparator K3 limits the voltage of capacitance
C
soft start
(and also at K2!) to a maximum
of + 5 V. The voltage at the ramp generator output may, however, rise to 5.5 V. With a
corresponding slope of the rising ramp generator edge, the duty cycle can be limited to
a desired maximum value.
Comparator K4
The comparator has its switching threshold at 1.5 V and sets the error flipflop with its
output if the voltage at capacitance
C
soft start
is below 1.5 V. However, the error flipflop
accepts the set signal only if no reset pulse (error) is applied. In this way the outputs
cannot be turned on again as long as an error signal is present.
Soft Start
The lower one of the two voltages at the plus inputs of K2 is a measure for the duty cycle
at the output. At the instant of turning on the component, the voltage at capacitor
C
soft start
equals 0 V. As long as no error is present, this capacitor is charged with a current of 6
μ
A
at the maximum value of 5 V. In case of an error,
C
soft start
is discharged with a current of
2
μ
A. A set signal is pending at the error flipflop below a charge of 1.5 V and the outputs
are enabled if no reset signal is pending simultaneously. As the minimum ramp
generator voltage, however, is 1.8 V, the duty cycle at the outputs is actually increased
slowly and continuously not before the voltage at
C
soft start
exceeds 1.8 V.
Error Flipflop
Error signals, which are led to input R of the error flipflop cause an immediate disabling
of the outputs, and after the error has been eliminated, the component to switch on again
by the soft start.
Comparator K5, K8,
V
REF
Overcurrent Load
These are error detectors which cause immediate disabling of the outputs via the error
flipflop when an error occurs. After elimination of the error, the component switches on
again by the soft start.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA4716C | IC for Switched-Mode Power Supplies (SMPS) |
| TDA4814 | Power Factor Controller IC for High Power Factor and Active Harmonic Filter |
| TDA4817 | Power Factor Controller IC for High Power Factor and Active Harmonic Filtering |
| TDA4817G | Power Factor Controller IC for High Power Factor and Active Harmonic Filtering |
| TDA4862 | Power-Factor Controller PFC IC for High Power Factor and Active Harmonic Filter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA4716C | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:IC for Switched-Mode Power Supplies (SMPS) |
| TDA4718A | 制造商:Siemens 功能描述:Semiconductor (D.I.P. IC) |
| TDA4722 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Color Processor for VCR |
| TDA4724 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Color Processor for VCR |
| TDA4725 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SECAM-L CHROMINANCE PROCESSOR FOR VHS VIDEO RECORDERS |
發布緊急采購，3分鐘左右您將得到回復。