- 您現在的位置：買賣IC網 > PDF目錄384964 > TDA1085CD (MOTOROLA INC) UNIVERSAL MOTOR SPEED CONTROLLER PDF資料下載
參數資料
| 型號： | TDA1085CD |
| 廠商： | MOTOROLA INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | UNIVERSAL MOTOR SPEED CONTROLLER |
| 中文描述： | UNIVERSAL MOTOR CONTROLLER, 0.2 A, PDSO16 |
| 封裝： | PLASTIC, SO-16 |
| 文件頁數： | 4/12頁 |
| 文件大?。?/td> | 170K |
| 代理商： | TDA1085CD |
TDA1085C
GENERAL DESCRIPTION
4
MOTOROLA ANALOG IC DEVICE DATA
The TDA 1085C triggers a triac accordingly to the speed regulation
requirements. Motor speed is digitally sensed by a tachogenerator
and then converted into an analog voltage.
The speed set is externally fixed and is applied to the internal linear
regulation input after having been submitted to programmable
acceleration ramps. The overall result consists in a full motor speed
range with two acceleration ramps which allow efficient washing
machine control (Distribute function).
Additionally, the TDA 1085C protects the whole system against AC
line stop or variations, overcurrent in the motor and tachogenerator
failure.
INPUT/OUTPUT FUNCTIONS
(Refer to Figures 1 and 8)
Voltage Regulator – (Pins 9 and 10)
This is a parallel type regulator
able to sink a large amount of current and offering good
characteristics. Current flow is provided from AC line by external
dropping resistors R1, R2, and rectifier: This half wave current is
used to feed a smoothering capacitor, the voltage of which is
checked by the IC.
When VCC is reached, the excess of current is derived by another
dropping resistor R10 and by Pin 10. These three resistors must be
determined in order:
To let 1.0 mA flow through Pin 10 when AC line is minimum and VCC
consumption is maximum (fast ramps and pulses present).
To let V10 reach 3.0 V when AC line provides maximum current and
VCC consumption is minimum (no ramps and no pulses).
All along the main line cycle, the Pin 10 dynamic range must not be
exceeded unless loss of regulation.
An AC line supply failure would cause shut down.
The double capacitive filter built with R1 and R2 gives an efficient
VCC smoothing and helps to remove noise from set speeds.
Speed Sensing – (Pins 4, 11, 12)
The IC is compatible with an
external analog speed sensing: its output must be applied to Pin 4,
and Pin 12 connected to Pin 8.
In most of the applications it is more convenient to use a digital
speed sensing with an unexpensive tachogenerator which
doesn
′
t need any tuning. During every positive cycle at Pin 12,
the capacitor CPin 11 is charged to almost VCC and during this
time, Pin 4 delivers a current which is 10 times the one charging
CPin 11. The current source gain is called G and is tightly
specified, but nevertheless requires an adjustment on RPin 4. The
current into this resistor is proportional to CPin 11 and to the motor
speed; being filtered by a capacitor, VPin 4 becomes smothered
and represents the “true actual motor speed”.
To maintain linearity into the high speed range, it is important to verify
that CPin 11 is fully charged: the internal source on Pin 11 has 100 K
impedance. Nevertheless CPin 11 has to be as high as possible as it
has a large influence on FV/C temperature factor. A 470 K
resistor
between Pins 11 and 9 reduces leakage currents and temperature
factor as well, down to neglectable effects.
Pin 12 also has a monitoring function: when its voltage is above
5.0 V, the trigger pulses are inhibited and the IC is reset. It also
senses the tachogenerator continuity, and in case of any circuit
aperture, it inhibits pulse, avoiding the motor to run out of control. In
the TDA 1085C, Pin 12 is negatively clamped by an internal diode
which removes the necessity of the external one used in the former
circuit.
Ramp Generator – (Pins 5, 6, 7)
The true Set Speed value taken in
consideration by the regulation is the output of the ramp generator
(Pin 7). With a given value of speed set input (Pin 5), the ramp
generator charges an external capacitor CPin 7 up to the moment
VPin 5 (set speed) equals VPin 4 (true speed), see Figure 2. The IC
has an internal charging current source of 1.2mA and delivers it from
0 to 12 V at Pin 7. It is the high acceleration ramp (5.0 s typical) which
allows rapid motor speed changes without excessive strains on the
mechanics. In addition, the TDA 1085C offers the possibility to break
this high acceleration with the introduction of a low acceleration ramp
(called Distribution) by reducing the Pin 7 source current down to
5.0
μ
A under Pin 6 full control, as shown by following conditions:
Presence of high acceleration ramp VPin 5 > VPin 4
Distribution occurs in the VPin 4 range (true motor speed) defined
by VPin 6
VPin 4
2.0 VPin 6
For two fixed values of VPin 5 and VPin 6, the motor speed will have
high acceleration, excluding the time for VPin 4 to go from VPin 6
to two times this value, high acceleration again, up to the moment
the motor has reached the set speed value, at which it will stay,
see Figure 3.
Should a reset happen (whatever the cause would be), the above
mentioned successive ramps will be fully reprocessed from 0 to the
maximum speed. If VPin 6 = 0, only the high acceleration ramp
occurs.
To get a real zero speed position, Pin 5 has been designed in such a
way that its voltage from 0 to 80 mV is interpreted as a true zero. As
a consequence, when changing the speed set position, the designer
must be sure that any transient zero would not occur: if any, the entire
circuit will be reset.
As the voltages applied by Pins 5 and 6 are derived from the internal
voltage regulator supply and Pin 4 voltage is also derived from the
same source, motor speed (which is determined by the ratios
between above mentioned voltages) is totally independent from VCC
variations and temperature factor.
Control Amplifier – (Pin 16)
It amplifies the difference between true
speed (Pin 4) and set speed (Pin 5), through the ramp generator. Its
output available at Pin 16 is a double sense current source with a
maximum capability of
±
100
μ
A and a specified transconductance
(340
μ
A/V typical). Pin 16 drives directly the trigger pulse generator,
and must be loaded by an electrical network which compensates the
mechanical characteristics of the motor and its load, in order to
provide stability in any condition and shortest transient response; see
Figure 4.
This network must be adjusted experimentally.
In case of a periodic torque variations, Pin 16 directly provides the
phase angle oscillations.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA1185A | Triac Phase Angle Controller |
| TDA1512 | 12 TO 20 W HI FI AUDIO POWER AMPLIFIER |
| TDA1512A | 12 TO 20 W HI FI AUDIO POWER AMPLIFIER |
| TDA1512AQ | 12 TO 20 W HI FI AUDIO POWER AMPLIFIER |
| TDA1520B | 20 W HI FI AUDIO POWER AMLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA1085CG | 功能描述:馬達/運動/點火控制器和驅動器 Universal Motor Speed Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TDA1085CG | 制造商:ON Semiconductor 功能描述:Power Supply IC |
| TDA10H0JB1 | 功能描述:DIP 開關/ SIP 開關 SM HalfPitch DIP Swt SPST, 10 POS, JTerm RoHS:否 制造商:Omron Electronics 位置數量:10 開關類型:DIP 執行器:Rotary 端子節距:2.54 mm 觸點形式: 端接類型:Solder Pin 電流額定值:100 mA 電壓額定值 DC: 工作溫度范圍: 安裝:Through Hole |
| TDA10H0JB1R | 功能描述:DIP 開關/ SIP 開關 SM HalfPitch DIP Swt SPST, 10 POS, JTerm RoHS:否 制造商:Omron Electronics 位置數量:10 開關類型:DIP 執行器:Rotary 端子節距:2.54 mm 觸點形式: 端接類型:Solder Pin 電流額定值:100 mA 電壓額定值 DC: 工作溫度范圍: 安裝:Through Hole |
| TDA10H0SB1 | 功能描述:DIP 開關/ SIP 開關 HALF PITCH 10 POS RoHS:否 制造商:Omron Electronics 位置數量:10 開關類型:DIP 執行器:Rotary 端子節距:2.54 mm 觸點形式: 端接類型:Solder Pin 電流額定值:100 mA 電壓額定值 DC: 工作溫度范圍: 安裝:Through Hole |
發布緊急采購，3分鐘左右您將得到回復。