參數資料
型號： TCM129C16A
廠商： Texas Instruments, Inc.
元件分類： Codec
英文描述： Combined Single-Chip PCM Codec And Filter(單片PCM編碼譯碼器和濾波器)
中文描述： 結合單芯片的PCM編解碼器和過濾器（單片的PCM編碼譯碼器和濾波器）
文件頁數： 18/25頁
文件大小： 392K
代理商： TCM129C16A
TCM29C13A, TCM29C14A, TCM29C16A, TCM29C17A,
TCM129C13A, TC,129C14A, TCM129C16A, TCM129C17A
COMBINED SINGLE-CHIP PCMCODEC AND FILTER
SCTS030E – AUGUST 1989 – REVISED OCTOBER 1996
18
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
system reliability and design considerations
TCM29C13A, TCM29C14A, TCM29C16A, TCM29C17A, TCM129C13A, TCM129C14A, TCM129C16A, and
TCM129C17A system reliability and design considerations are described in the following paragraphs.
latch-up
Latch-up is possible in all CMOS devices. It is caused by the firing of a parasitic SCR that is present due to the
inherent nature of CMOS. When a latch-up occurs, the device draws excessive amounts of current and will
continue to draw heavy current until power is removed. Latch-up can result in permanent damage to the device
if supply current to the device is not limited.
Even though the TCM29CxxA and TCM129CxxA devices are heavily protected against latch-up, it is still
possible to cause latch-up under certain conditions in which excess current is forced into or out of one or more
terminals. Latch-up can occur when the positive supply voltage drops momentarily below ground, when the
negative supply voltage rises momentarily above ground, or possibly if a signal is applied to a terminal after
power has been applied but before the ground is connected. This can happen if the device is hot-inserted into
a card with the power applied, or if the device is mounted on a card that has an edge connector, and the card
is hot-inserted into a system with the power on.
To help ensure that latch-up does not occur, it is considered good design practice to connect a reverse-biased
Schottky diode (with a forward voltage drop of less than or equal to 0.4 V — 1N5711 or equivalent), between
each power supply and GND (see Figure 7). If it is possible that a TCM29CxxA- or TCM129CxxA-equipped card
that has an edge connector could be hot-inserted into a powered-up system, it is also important to ensure that
the ground edge connector traces are longer than the power and signal traces so that the card ground is always
the first to make contact.
device power-up sequence
Latch-up also can occur if a signal source is connected without the device being properly grounded. A signal
applied to one terminal could then find a ground through another signal terminal on the device. To ensure proper
operation of the device and as a safeguard against this sort of latch-up, it is recommended that the following
power-up sequence always be used:
1.
Ensure no signals are applied to the device before the power-up sequence is complete.
2.
Connect GND.
3.
Apply V
BB
(most negative voltage).
Apply V
CC
(most positive voltage).
Force a power down condition in the device.
4.
5.
6.
Connect clocks.
7.
Release the power-down condition.
8.
Apply FSX and/or FXR synchronization pulses.
9.
Apply signal inputs.
When powering down the device, this procedure should be followed in the reverse order.
相關PDF資料
PDF描述
TCM129C16AN COMBINED SINGLE-CHIP PCM CODEC AND FILTER
TCM3105DJE FSK MODEM
TCM3105DNL FSK MODEM
TCM3105 FSK MODEM
TCM3105DNE FSK MODEM
相關代理商/技術參數
參數描述
TCM129C16ADW 制造商:TI 制造商全稱:Texas Instruments 功能描述:COMBINED SINGLE-CHIP PCM CODEC AND FILTER
TCM129C16AN 制造商:TI 制造商全稱:Texas Instruments 功能描述:COMBINED SINGLE-CHIP PCM CODEC AND FILTER
TCM129C16DW 制造商:Rochester Electronics LLC 功能描述:- Bulk
TCM129C16N 制造商:Rochester Electronics LLC 功能描述:- Bulk
TCM129C17 制造商:TI 制造商全稱:Texas Instruments 功能描述:COMBINED SINGLE-CHIP PCM CODEC AND FILTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*