參數資料
型號： TC94A23F
元件分類： 消費家電
英文描述： SPECIALTY CONSUMER CIRCUIT, PQFP100
封裝： 14 X 20 MM, 2.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100
文件頁數： 5/20頁
文件大?。?/td> 339K
代理商： TC94A23F
TC94A23F
2002-02-06
13
Pin
Number
Symbol
Pin Name
Function and Operation
Remarks
92
INTR
External interrupt
input
External interrupt input pin.
When interrupts are enabled and a pulse of
1.11 to 3.33 s or more (13.3 to 40 s when
the 75 kHz clock is used) is input to this pin,
an interrupt is generated and the program
jumps to address 1. Input logic and
rising/falling edge can be individually selected
for interrupt inputs.
The internal 8-bit timer clock can be selected
for interrupt inputs. Interrupts can be
generated (address 3) by pulse count or the
count value.
Interrupt inputs are Schmidt inputs. The pin
can be used as an input port for inputs such
as remote control signals.
93
MXO
94
MXI
Crystal oscillator pins
for controller
Crystal oscillator pins for the controller.
The oscillator clock is used as a time base for
the clock function as well as the system clock
for the controller. After system reset, the CPU
starts operation using the 16.9344 MHz CD
oscillator (connected to the XI and XO pins).
The oscillator is switched to the controller
oscillator by program. Either a 4.5 MHz
reference oscillator or a 75 kHz oscillator is
connected to the MXO and MXI pins.
The oscillators are switched by a bit used to
select a frequency of 4.5 MHz or 75 kHz. The
oscillators incorporate a feedback resistor.
Switching frequencies automatically switches
the feedback resistor of the crystal oscillator.
75 kHz: Rout2
2 K , RfXT2
10 M
typ.
4.5 MHz: Rout2
2 K , RfXT2
1 M
typ.
If the operating clock is the CD crystal
oscillator, fix the MXI pin to GND.
During execution of the CKSTP instruction,
oscillation halts.
Selection and control of crystal oscillators are
done by program.
(Note)
When the 75 kHz crystal oscillator is
used, externally add/connect a
100 k
output resistor.
19, 96
MVDD
20, 95
MVSS
Power supply pins for
controller block
Power supply pins for the controller block.
Normally, VDD
4.5 to 5.5 V.
In backup state (when executing the CKSTP
instruction), current dissipation becomes low
(1 A or below), dropping the power supply
voltage to 2.0 V.
If 2.7 V or more is applied to these pins when
at 0 V, a system reset is applied to the device
and the program starts from address 0
(power-on reset).
The CD processor incorporates a power
supply detector, which detects the power
supply voltage of 2.5 V.
(Note)
At power-on reset operation, allow
10 to 100 ms while the device power
supply voltage rises.
When not using the power supply detector
function, set the test port pins (TEST#0 to 3)
to all 1s so that the CD processor enters Halt
state. Setting to Halt state reduces current
dissipation by 150 A (typ.).
MVDD
MXO
Rout2
RfXT2
MXI
MVDD
MVSS
相關PDF資料
PDF描述
TC94A29FAG SPECIALTY CONSUMER CIRCUIT, PQFP64
TC94A29FB SPECIALTY CONSUMER CIRCUIT, PQFP64
TC962MJA SWITCHED CAPACITOR CONVERTER, 24 kHz SWITCHING FREQ-MAX, CDIP8
TC962IJAG SWITCHED CAPACITOR CONVERTER, 24 kHz SWITCHING FREQ-MAX, CDIP8
TC962EPAG SWITCHED CAPACITOR CONVERTER, 24 kHz SWITCHING FREQ-MAX, PDIP8
相關代理商/技術參數
參數描述
TC94A29FAG 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
TC94A29FB 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
TC94A39 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:CMOS Digital Intergrated Circuit
TC94A39FAG 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Single-Chip CD Processor with Built-in Controller (CD-DX)
TC94A39FAG/FB 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:CMOS Digital Intergrated Circuit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*