- 您現在的位置：買賣IC網 > PDF目錄98185 > TC9446FG SPECIALTY CONSUMER CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | TC9446FG |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 封裝： | 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 14/41頁 |
| 文件大?。?/td> | 562K |
| 代理商： | TC9446FG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
TC9446FG
2005-09-28
21
3.
Setting Procedure Until it Starts Decode Program Operation
Setting procedure until it starts operation of the decode program built in TC9446FG is shown below.
First, 10 words program data is transmitted in the program boot mode after release of the power-on reset
at the time of a power-supply injection.
However, when there is a program required for others, program data of a maximum of 128 words can be
transmitted.
And, if the command of soft reset-off is transmitted, a program will begin to operate and decode will be
started by transmitting addresses of the write-in command shown in an attached sheet (the program
explanation data) after that 9 words of 0000h-0008h.
Procedure until it starts operation of a decode program to Figure 15 is shown.
Note 7: Internal RAM is cleared, in order to muting for output, after transmitting a setup of command 0003h “decode
off” in the case of AC-3 decoder program. Please transmit following data after checking that ACK is set to
“L” from “H”, since such a case has the time for about 23 ms (maximum) in this processing. If processing of
the internal RAM clearance by the “decode off” command is completed, it will return at the waiting time for 1
or less ms.
In addition, according to the kind of decode program, please transmit following data after checking that ACK
is set to “L” from “H”, since the waiting time which the data transmission at the time of decode on/off takes
differs.
Figure 15
Procedure to Decode Program Operation Start
Program boot
Soft reset OFF
Starting of decode
Power ON reset
Write-in command transmission.
(9 word of 0000h to 0008h)
(9 word of continuing from 0000h are transmitted.)
相關PDF資料 |
PDF描述 |
|---|---|
| TC9447F | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| TC9452F | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| TC9456F | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| TC9459F | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TC9459N | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDIP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC9447F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Single-Chip Audio Digital Signal Processor |
| TC9452F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:SINGLE CHIP SURROUND LSI |
| TC9455F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic |
| TC9455N | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic |
| TC9456F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:SINGLE CHIP SURROUND LSI WITH A BUILT-IN SRS |
發布緊急采購，3分鐘左右您將得到回復。