參數資料
型號： TC9402CPD
元件分類： 模擬專用變換器
英文描述： VOLTAGE-FREQUENCY CONVERTER, 0.1 MHz, PDIP14
封裝： PLASTIC, DIP-14
文件頁數： 27/28頁
文件大?。?/td> 545K
代理商： TC9402CPD
TC9400/9401/9402
DS21483D-page 8
2007 Microchip Technology Inc.
3.0
DETAILED DESCRIPTION
3.1
Voltage-to-Frequency (V/F) Circuit
Description
The TC9400 V/F converter operates on the principal of
charge balancing. The operation of the TC9400 is
easily understood by referring to Figure 3-1. The input
voltage (VIN) is converted to a current (IIN) by the input
resistor. This current is then converted to a charge on
the integrating capacitor and shows up as a linearly
decreasing voltage at the output of the op amp. The
lower limit of the output swing is set by the threshold
detector, which causes the reference voltage to be
applied to the reference capacitor for a time period long
enough to charge the capacitor to the reference volt-
age. This action reduces the charge on the integrating
capacitor by a fixed amount (q = CREF x VREF), causing
the op amp output to step up a finite amount.
At the end of the charging period, CREF is shorted out.
This dissipates the charge stored on the reference
capacitor, so that when the output again crosses zero,
the system is ready to recycle. In this manner, the con-
tinued discharging of the integrating capacitor by the
input is balanced out by fixed charges from the refer-
ence voltage. As the input voltage is increased, the
number of reference pulses required to maintain
balance increases, which causes the output frequency
to also increase. Since each charge increment is fixed,
the increase in frequency with voltage is linear. In
addition, the accuracy of the output pulse width does
not directly affect the linearity of the V/F. The pulse
must simply be long enough for full charge transfer to
take place.
The TC9400 contains a “self-start” circuit to ensure the
V/F converter always operates properly when power is
first applied. In the event that, during power-on, the op
amp output is below the threshold and CREF is already
charged, a positive voltage step will not occur. The op
amp output will continue to decrease until it crosses the
-3.0V threshold of the “self-start” comparator. When
this happens, an internal resistor is connected to the op
amp input, which forces the output to go positive until
the TC9400 is in its normal Operating mode.
The TC9400 utilizes low-power CMOS processing for
low input bias and offset currents, with very low power
dissipation. The open drain N-channel output FETs
provide high voltage and high current sink capability.
FIGURE 3-1:
10 Hz to 10 kHz V/F Converter.
–
+
+5V
14
VDD
+5V
RL
10 k
Ω
RL
10 k
Ω
8
10
9
FOUT
FOUT/2
11
3ms
Delay
Self-
Start
12
5
20 k
Ω
60 pF
Op Amp
CINT
820 pF
CREF
180 pF
12 pF
RIN
1M
Ω
VIN
+5V
-5V
50 k
Ω
510 k
Ω
10 k
Ω
3
1
Offset
Adjust
IIN
Zero Adjust
0V –10V
IBIAS
VSS
4
-5V
2
Output
Common
VREFOUT
RBIAS
100 k
Ω
AMP OUT
TC9400
TC9401
TC9402
GND
6
Threshold
Detector
Threshold
Detect
Reference Voltage
(Typically -5V)
÷2
VREF
7
-3V
INPUT
相關PDF資料
PDF描述
TC9400CPDG VOLTAGE-FREQUENCY CONVERTER, 0.1 MHz, PDIP14
TC9401CPD VOLTAGE-FREQUENCY CONVERTER, 0.1 MHz, PDIP14
TC9400COD VOLTAGE-FREQUENCY CONVERTER, 0.1 MHz, PDSO14
TC9401EJD VOLTAGE-FREQUENCY CONVERTER, 0.1 MHz, CDIP14
TC9400CPD VOLTAGE-FREQUENCY CONVERTER, 0.1 MHz, PDIP14
相關代理商/技術參數
參數描述
TC9402CPD 制造商:Microchip Technology Inc 功能描述:IC F/V-V/F CONVERTER
TC9402CPD 制造商:Microchip Technology Inc 功能描述:V/F Converter
TC9402EJD 功能描述:電壓頻率轉換及頻率電壓轉換 V/F Converter RoHS:否 制造商:Texas Instruments 全標度頻率:4000 KHz 線性誤差:+/- 1 % FSR 電源電壓-最大: 電源電壓-最小: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 安裝風格:Through Hole 封裝 / 箱體:PDIP-14 封裝:Tube
TC9404FN 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:MODULATION SYSTEM DA CONVERTER WITH ANALOG FILTER
TC9404FNG 制造商:Toshiba 功能描述:1Bit Cut Tape
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*