- 您現在的位置：買賣IC網 > PDF目錄361413 > TC9400COD (TelCom Semiconductor, Inc.) VOLTAGE-TO-FREQUENCY/FREQUENCY-TO-VOLTAGE CONVERTERS PDF資料下載
參數資料
| 型號： | TC9400COD |
| 廠商： | TelCom Semiconductor, Inc. |
| 英文描述： | VOLTAGE-TO-FREQUENCY/FREQUENCY-TO-VOLTAGE CONVERTERS |
| 中文描述： | VOLTAGE-TO-FREQUENCY/FREQUENCY-TO-VOLTAGE變換器 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 154K |
| 代理商： | TC9400COD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁
3-294
TELCOM SEMICONDUCTOR, INC.
VOLTAGE-TO-FREQUENCY/
FREQUENCY-TO-VOLTAGE CONVERTERS
TC9400
TC9401
TC9402
C
REF
The exact value is not critical and may be used to trim the
full-scale frequency (see "Input/Output Relationships"). Glass
film or air trimmer capacitors are recommended because of
their stability and low leakage. Locate as close as possible
to pins 5 and 3.
V
DD
, V
SS
Power supplies of
±
5V are recommended. For high-
accuracy requirements, 0.05% line and load regulation and
0.1
μ
F disc decoupling capacitors located near the pins are
recommended.
Adjustment Procedure
Figure 1 shows a circuit for trimming the zero location.
Full scale may be trimmed by adjusting R
IN
, V
REF
, or C
REF
.
Recommended procedure for a 10kHz full-scale frequency
is as follows:
(1) Set V
IN
to 10 mV and trim the zero adjust circuit to
obtain a 10Hz output frequency.
(2) Set V
IN
to 10V and trim either R
IN
, V
REF
, or C
REF
to
obtain a 10kHz output frequency.
If adjustments are performed in this order, there should be
no interaction and they should not have to be repeated.
Figure 3. Recommended C
REF
vs V
REF
500
400
300
200
100
0
–1
–2
–3
VREF (V)
–4
–5
–6
–7
CR
1 kHz
100kHz
VDD = +5V
VSS = – 5V
RIN = 1M
VIN = +10V
TA = +25°C
Improved Single Supply V/F Converter
Operation
A TC9400 which operates from a single 12 to 15V
variable power source is shown in Figure 5. This circuit uses
two Zener diodes to set stable biasing levels for the TC9400.
The Zener diodes also provide the reference voltage, so the
output impedance and temperature coefficient of the Zeners
will directly affect power supply rejection and temperature
performance.
Full scale adjustment is accomplished by trimming the
input current. Trimming the reference voltage is not recom-
mended for high accuracy applications unless an op amp is
used as a buffer, because the TC9400 requires a low
impedance reference (see the V
REF
pin description section
for more information).
The circuit of Figure 5 will directly interface with CMOS
logic operating at 12V to 15V. TTL or 5V CMOS logic can be
accommodated by connecting the output pullup resistors to
the +5V supply. An optoisolator can also be used if an
isolated output is required.
相關PDF資料 |
PDF描述 |
|---|---|
| TC9401EJD | VOLTAGE-TO-FREQUENCY/FREQUENCY-TO-VOLTAGE CONVERTERS |
| TC9402EJD | POT 1.0K OHM 6MM CERMET TOP SMD |
| TC9491ACOA | LOW POWER, BANDGAP VOLTAGE REFERENCES |
| TC9491A | LOW POWER, BANDGAP VOLTAGE REFERENCES |
| TC9491ACZM | LOW POWER, BANDGAP VOLTAGE REFERENCES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC9400COD713 | 功能描述:電壓頻率轉換及頻率電壓轉換 V/F Converter RoHS:否 制造商:Texas Instruments 全標度頻率:4000 KHz 線性誤差:+/- 1 % FSR 電源電壓-最大: 電源電壓-最小: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 安裝風格:Through Hole 封裝 / 箱體:PDIP-14 封裝:Tube |
| TC9400CPD | 功能描述:電壓頻率轉換及頻率電壓轉換 V/F Converter RoHS:否 制造商:Texas Instruments 全標度頻率:4000 KHz 線性誤差:+/- 1 % FSR 電源電壓-最大: 電源電壓-最小: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 安裝風格:Through Hole 封裝 / 箱體:PDIP-14 封裝:Tube |
| TC9400CPD | 制造商:Microchip Technology Inc 功能描述:IC F/V-V/F CONVERTER 9400 DIP14 |
| TC9400CPD | 制造商:Microchip Technology Inc 功能描述:IC F/V-V/F CONVERTER 9400 DIP14 |
| TC9400EJD | 功能描述:電壓頻率轉換及頻率電壓轉換 V/F Converter RoHS:否 制造商:Texas Instruments 全標度頻率:4000 KHz 線性誤差:+/- 1 % FSR 電源電壓-最大: 電源電壓-最小: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 安裝風格:Through Hole 封裝 / 箱體:PDIP-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。