• <label id="vnyii"><menuitem id="vnyii"><abbr id="vnyii"></abbr></menuitem></label>
    <pre id="vnyii"><fieldset id="vnyii"></fieldset></pre>
    <tbody id="vnyii"></tbody>
    <wbr id="vnyii"><menuitem id="vnyii"></menuitem></wbr>
    參數資料
    型號: TC7136CPL
    元件分類: ADC
    英文描述: 1-CH DUAL-SLOPE ADC, PDIP40
    封裝: PLASTIC, DIP-40
    文件頁數: 3/15頁
    文件大小: 134K
    代理商: TC7136CPL
    11
    Low Power 3-1/2 Digit Analog-To-
    Digital Converters
    TC7136
    TC7136A
    TC7136-6
    10/18/96
    2001 Microchip Technology Inc.
    DS21461A
    V
    ANALOG
    COMMON
    TC7136
    TC7136A
    VREF
    +
    32
    35
    36
    26
    240 k
    10 k
    VREF
    VREF
    1
    +
    9V
    SET VREF = 1/2 VFULL SCALE
    V
    +
    temperature stability (typically 35 ppm/
    °c). for TC7136A
    This potential can be used to generate the TC7136A's
    reference voltage. An external voltage reference will be
    unnecessary in most cases because of the 35 ppm/
    °C
    temperature coefficient. See TC7136A Internal Voltage
    Reference discussion.
    TEST (Pin 37)
    The TEST pin potential is 5V less than V+. TEST may be
    used as the negative power supply connection for external
    CMOS logic. The TEST pin is tied to the internally-generated
    negative logic supply through a 500
    resistor. The TEST pin
    load should not be more than 1mA. See the Applications
    Section for additional information on using TEST as a
    negative digital logic supply.
    If TEST is pulled high (to V+), all segments plus the
    minus sign will be activated. DO NOT OPERATE IN THIS
    MODE FOR MORE THAN SEVERAL MINUTES. With TEST
    = V+, the LCD segments are impressed with a DC voltage
    which will destroy the LCD.
    TC7136A Internal Voltage Reference
    The TC7136 analog common voltage temperature sta-
    bility has been significantly improved (Figure 9). The "A"
    version of the industry-standard TC7136 device allows
    users to upgrade old systems and design new systems
    without external voltage references. External R and C val-
    ues do not need to be changed; however, noise perfor-
    mance will be improved by increasing CAZ. (See Auto-Zero
    Capacitor section.) Figure 10 shows analog common sup-
    plying the necessary voltage reference for the TC7136/A.
    APPLICATIONS INFORMATION
    Figure 9. Analog Common Temperature Coefficient
    Decimal Point and Annunciator Drive
    The TEST pin is connected to the internally-generated
    digital logic supply ground through a 500
    resistor. The
    TEST pin may be used as the negative supply for external
    CMOS gate segment drivers. LCD annunciators for decimal
    points, low battery indication, or function indication may be
    added without adding an additional supply. No more than 1
    mA should be supplied by the TEST pin: its potential is
    approximately 5V below V+.
    TYPICAL
    MAXIMUM
    TYPICAL
    NO MAXIMUM
    SPECIFIED
    200
    180
    160
    140
    120
    100
    80
    60
    40
    20
    0
    ANALOG
    COMMON
    TEMPERATURE
    COEFFICIENT
    (ppm/
    °C)
    TC7136
    TC7136A
    ICL7136
    Figure 10. TC7136A Internal Voltage Reference Connection
    Liquid Crystal Display Sources
    Several manufacturers supply standard LCDs to inter-
    face with the TC7136A 3-1/2 digit analog-to-digital con-
    verter.
    Representative
    Manufacturer
    Address/Phone
    Part Numbers*
    Crystaloid
    5282 Hudson Dr.
    C5335, H5535,
    Electronics
    Hudson, OH 44236
    T5135, SX440
    216-655-2429
    AND
    720 Palomar Ave.
    FE 0201, 0501
    Sunnyvale, CA 94086
    FE 0203, 0701
    408-523-8200
    FE 2201
    VGI, Inc.
    1800 Vernon St. Ste. 2
    I1048, I1126
    Roseville, CA 95678
    916-783-7878
    Hamlin, Inc.
    612 E. Lake St.
    3902, 3933, 3903
    Lake Mills, WI 53551
    414-648-2361
    *NOTE: Contact LCD manufacturer for full product listing/specifications.
    相關PDF資料
    PDF描述
    TC7136ACPL 1-CH DUAL-SLOPE ADC, PDIP40
    TC7136RCPL 1-CH DUAL-SLOPE ADC, PDIP40
    TC7136RCKW 1-CH DUAL-SLOPE ADC, PQFP44
    TC7136ACPL 1-CH DUAL-SLOPE ADC, PDIP40
    TC7136ARCPL 1-CH DUAL-SLOPE ADC, PDIP40
    相關代理商/技術參數
    參數描述
    TC7136RCPL 功能描述:LCD 驅動器 Low Power RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
    TC713A 制造商:Thomas & Betts 功能描述:Fittings Connector 1inch Steel
    TC713A-RT 制造商:Thomas & Betts 功能描述:Fittings Connector 1inch Steel
    TC714A 制造商:Thomas & Betts 功能描述:Fittings Connector 1.25inch Steel
    TC714A-RT 制造商:Thomas & Betts 功能描述:Fittings Connector 1.25inch Male Steel