- 您現在的位置：買賣IC網 > PDF目錄98171 > TC7106CPLG 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 PDF資料下載
參數資料
| 型號： | TC7106CPLG |
| 元件分類： | ADC |
| 英文描述： | 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-40 |
| 文件頁數： | 4/34頁 |
| 文件大?。?/td> | 482K |
| 代理商： | TC7106CPLG |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
TC7106/A/TC7107/A
DS21455D-page 12
2008 Microchip Technology Inc.
6.0
DIGITAL SECTION (TC7107A)
Figure 6-2 shows a TC7106A block diagram. It is
designed to drive common anode LEDs. It is identical
to the TC7106A, except that the regulated supply and
backplane drive have been eliminated and the segment
drive is typically 8 mA. The 1000’s output (Pin 19) sinks
current from two LED segments, and has a 16 mA drive
capability.
In both devices, the polarity indication is “ON” for
negative analog inputs. If VIN- and VIN+ are reversed,
this indication can be reversed also, if desired.
The display font is the same as the TC7106A.
6.1
System Timing
The oscillator frequency is divided by 4 prior to clocking
the
internal
decade
counters.
The
four-phase
measurement cycle takes a total of 4000 counts, or
16,000 clock pulses. The 4000-count cycle is indepen-
dent of input signal magnitude.
Each phase of the measurement cycle has the
following length:
1.
Auto-zero phase: 1000 to 3000 counts (4000 to
12000 clock pulses).
For signals less than full scale, the auto-zero phase is
assigned the unused reference integrate time period:
2.
Signal integrate: 1000 counts (4000 clock
pulses).
This time period is fixed. The integration period is:
EQUATION 6-1:
3.
Reference Integrate: 0 to 2000 counts (0 to 8000
clock pulses).
The TC7106A/TC7107A are drop-in replacements for
the TC7106/TC7107 parts. External component value
changes are not required to benefit from the low drift
internal reference.
6.2
Clock Circuit
Three clocking methods may be used (see Figure 6-1):
1.
An external oscillator connected to Pin 40.
2.
A crystal between Pins 39 and 40.
3.
An RC oscillator using all three pins.
FIGURE 6-1:
Clock Circuits.
Where:
FOSC
=
Externally set clock frequency
T
SI
4
F
OSC
-------------
1000
×
=
TC7106A
TC7107A
4
Crystal
RC Network
40
38
EXT
OSC
39
To TEST Pin on TSC7106A
To GND Pin on TSC7107A
To
Counter
相關PDF資料 |
PDF描述 |
|---|---|
| TC7107AIPL | 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 |
| TC7106IPL | 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 |
| TC7106ACPLG | 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 |
| TC7107ACPL | 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 |
| TC7107CKW713 | 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC7106IJL | 功能描述:LCD 驅動器 3-1/2 Digit A/D w/ LCD Driver RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| TC7106IKW | 功能描述:LCD 驅動器 w/LCD Driver RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| TC7106IPL | 功能描述:LCD 驅動器 w/LCD Driver RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| TC7106RCPL | 功能描述:LCD 驅動器 w/LCD Driver RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| TC7107 | 制造商:TELCOM 制造商全稱:TelCom Semiconductor, Inc 功能描述:3-1/2 DIGIT A/D CONVERTERS |
發布緊急采購，3分鐘左右您將得到回復。