參數資料
型號： TC649VUA
元件分類： 運動控制電子
英文描述： BRUSHLESS DC MOTOR CONTROLLER, PDSO8
封裝： PLASTIC, MSOP-8
文件頁數： 7/28頁
文件大?。?/td> 478K
代理商： TC649VUA
2002 Microchip Technology Inc.
DS21449C-page 15
TC649
5.6
Latch-up Considerations
As with any CMOS IC, the potential exists for latch-up
if signals are applied to the device which are outside
the power supply range. This is of particular concern
during power-up if the external circuitry (such as the
sensor network, VAS divider or shutdown circuit) are
powered by a supply different from that of the TC649.
Care should be taken to ensure that the TC649’s VDD
supply powers up first. If possible, the networks
attached to VIN and VAS should connect to the VDD sup-
ply at the same physical location as the IC itself. Even
if the IC and any external networks are powered by the
same supply, physical separation of the connecting
points can result in enough parasitic capacitance and/
or inductance in the power supply connections to delay
one power supply “routing” versus another.
5.7
Power Supply Routing and
Bypassing
Noise present on the VIN and VAS inputs may cause
erroneous operation of the FAULT output. As a result,
these inputs should be bypassed with a 0.01 F
capacitor mounted as close to the package as possible.
This is especially true of VIN, which is usually drive from
a high impedance source (such as a thermistor). Addi-
tionally, the VDD input should be bypassed with a 1 F
capacitor with grounds being kept as short as possible.
To keep fan noise off the TC649 ground pin, individual
ground returns for the TC649 and the low side of the
fan current sense resistor should be used.
Design Example
Step 1. Calculate R1 and R2 based on using an NTC
having a resistance of 10 k
at TMIN (25°C)
and 4.65 k
at TMAX (45°C) (see Figure 5-9).
R1 = 20.5 k
R2 = 3.83 k
Step 2. Set auto-shutdown Level.
VAS = 1.8V.
Limit the divider current to 100 A
R5 = 33 k
R6 = 18 k
Step 3. Design the output circuit.
Maximum fan motor current = 250 mA.
Q1 beta is chosen at 50 from which
R7 = 800 .
FIGURE 5-9:
Design Example.
FAULT
SENSE
NTC
10 k
@ 25C
R1
20.5 k
R2
3.83 k
R5
33 k
R7
800
GND
RESET
Shutdown
(Optional)
Q1
+12V
+5V
VDD
VIN
VAS
VOUT
RSENSE
2.2
CSENSE
0.1 F
C1
1 F
CF
TC649
Fan
Fan Fault
CB
0.01 F
CB
0.01 F
CB
1 F
1
8
4
6
7
5
2
3
R6
18 k
Open-
Drain
Device
相關PDF資料
PDF描述
TL5002ID 0.1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8
TC53N3002ECTTR 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5
TL431ACZ-AP 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 2.495 V, PBCY3
TPS2383PMR 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP64
TPS3125J18DBVRG4 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5
相關代理商/技術參數
參數描述
TC649VUATR 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TC6-4A11 制造商:FERROXCUBE 制造商全稱:Ferroxcube International Holding B.V. 功能描述:Ferrite toroids
TC6-4C65 制造商:FERROXCUBE 制造商全稱:Ferroxcube International Holding B.V. 功能描述:Ferrite toroids
TC65 功能描述:鋁質電解電容器 - 帶引線 20uF 350Volts RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk
TC65 MODULE 制造商:Siemens 功能描述:GSM/GPRS JAVA MODULE & B2B
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*