- 您現在的位置：買賣IC網 > PDF目錄383931 > TC649 (Microchip Technology Inc.) PWM Fan Speed Controller with Auto-Shutdown and FanSense Technology(風扇監控器帶自動關斷功能) PDF資料下載
參數資料
| 型號： | TC649 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | PWM Fan Speed Controller with Auto-Shutdown and FanSense Technology(風扇監控器帶自動關斷功能) |
| 中文描述： | PWM風扇帶自動調速器關斷和FanSense科技（風扇監控器帶自動關斷功能） |
| 文件頁數： | 5/28頁 |
| 文件大小： | 478K |
| 代理商： | TC649 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
2002 Microchip Technology Inc.
DS21449C-page 5
TC649
3.0
DETAILED DESCRIPTION
3.1
PWM
The PWM circuit consists of a ramp generator and
threshold detector. The frequency of the PWM is
determined by the value of the capacitor connected to
the C
F
input. A frequency of 30 Hz is recommended for
most applications (C
F
= 1 μF). The PWM is also the
time base for the Start-up Timer (see Section 3.3,
“Start-up Timer”). The PWM voltage control range is
1.25V to 2.65V (typical) for 0% to 100% output duty
cycle.
3.2
V
OUT
Output
The V
OUT
pin is designed to drive a low cost transistor
or MOSFET as the low side power switching element in
the system. Various examples of driver circuits will be
shown throughout the datasheet. This output has
asymmetric complementary drive and is optimized for
driving NPN transistors or N-channel MOSFETs. Since
the system relies on PWM rather than linear control,
the power dissipation in the power switch is kept to a
minimum. Generally, very small devices (TO-92 or SOT
packages) will suffice.
3.3
Start-Up Timer
To ensure reliable fan start-up, the Start-up Timer turns
the V
OUT
output on for 32 cycles of the PWM whenever
the fan is started from the off state. This occurs at
power-up and when coming out of shutdown or auto-
shutdown mode. If the PWM frequency is 30 Hz (C
F
=
1 μF) the resulting start-up time will be approximately
one second. If a fan fault is detected (see Section 3.5,
FAULT Output), the Diagnostic Timer is triggered once,
followed by the Start-up Timer. If the fault persists, the
device is shut down (see Section 3.5, FAULT Output).
3.4
SENSE Input
(FanSense Technology)
The SENSE input (Pin 5) is connected to a low value
current sensing resistor in the ground return leg of the
fan circuit. During normal fan operation, commutation
occurs as each pole of the fan is energized. This
causes brief interruptions in the fan current, seen as
pulses across the sense resistor. If the device is not in
shutdown or auto-shutdown mode, and pulses are not
appearing at the SENSE input, a fault exists.
The short, rapid change in fan current (high dl/dt)
causes a corresponding dV/dt across the sense
resistor, R
SENSE
. The waveform on R
SENSE
is
differentiated and converted to a logic-level pulse-train
by C
SENSE
and the internal signal processing circuitry.
The presence and frequency of this pulse-train is a
direct indication of fan operation. See Section 5.0,
“Typical Applications”, for more details.
3.5
FAULT Output
Pulses appearing at SENSE due to the PWM turning
on are blanked, and the remaining pulses are filtered
by a missing pulse detector. If consecutive pulses are
not detected for thirty-two PWM cycles (
1 Sec if
C
F
= 1 μF), the Diagnostic Timer is activated, and
V
OUT
is driven high continuously for three PWM cycles
(
100 msec if C
F
= 1 μF). If a pulse is not detected
within this window, the Start-up Timer is triggered (see
Section 3.3, “Start-up Timer”). This should clear a tran-
sient fault condition. If the missing pulse detector times
out again, the PWM is stopped and FAULT goes low.
When FAULT is activated due to this condition, the
device is latched in shutdown mode and will remain off
indefinitely. The TC649 is thus prevented from
attempting to drive a fan under catastrophic fault
conditions.
One of two things will restore operation: Cycling power
off and then on again; or pulling V
IN
below V
SHDN
and
releasing it to a level above V
REL
. When one of these
two conditions is satisfied, the normal start-up cycle is
triggered and operation will resume, provided the fault
has been cleared.
3.6
Auto-Shutdown Mode
If the voltage on V
IN
becomes less than the voltage on
V
AS
, the fan is automatically shut off (auto-shutdown
mode). The TC649 exits auto-shutdown mode when
the voltage on V
IN
becomes higher than the voltage on
V
AS
by V
HAS
(the auto-shutdown hysteresis voltage,
see Figure 3-1). The Start-up Timer is triggered and
normal operation is resumed upon exiting auto-shut-
down mode. The FAULT output is unconditionally
inactive in auto-shutdown mode.
相關PDF資料 |
PDF描述 |
|---|---|
| TC649E | PWM Fan Speed Controller with Auto-Shutdown and FanSense⑩ Technology |
| TC649EPA | PWM Fan Speed Controller with Auto-Shutdown and FanSense⑩ Technology |
| TC649EUA | PWM Fan Speed Controller with Auto-Shutdown and FanSense⑩ Technology |
| TC6501P075VCT | Ultra Small Temperature Switches with Pin Selectable Hysteresis |
| TC6504N015VCT | Ultra Small Temperature Switches with Pin Selectable Hysteresis |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC649_13 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controller with Auto-Shutdown and FanSensea?￠ Technology |
| TC649B | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controllers With Auto-Shutdown, Fan Restart and FanSense⑩ Technology for Fault Detection |
| TC649BEOA | 功能描述:馬達/運動/點火控制器和驅動器 w/Rstrt Shtdn & Flt RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC649BEOA713 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controllers With Auto-Shutdown, Fan Restart and FanSense⑩ Technology for Fault Detection |
| TC649BEOATR | 功能描述:馬達/運動/點火控制器和驅動器 w/Rstrt Shtdn & Flt RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。