- 您現在的位置：買賣IC網 > PDF目錄98170 > TC647VUATR BRUSHLESS DC MOTOR CONTROLLER, PDSO8 PDF資料下載
參數資料
| 型號： | TC647VUATR |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| 封裝： | PLASTIC, MSOP-8 |
| 文件頁數： | 6/28頁 |
| 文件大?。?/td> | 478K |
| 代理商： | TC647VUATR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
TC647
DS21447C-page 14
2002 Microchip Technology Inc.
FIGURE 5-7:
Output Drive Transistor Circuit Topologies.
FIGURE 5-8:
Powering the Fan from a
-12V Supply.
5.6
Latch-Up Considerations
As with any CMOS IC, the potential exists for latch-up
if signals are applied to the device which are outside
the power supply range. This is of particular concern
during power-up if the external circuitry (such as the
sensor network, VMIN divider or shutdown circuit) is
powered by a supply different from that of the TC647.
Care should be taken to ensure that the TC647’s VDD
supply powers up first. If possible, the networks
attached to VIN and VMIN should connect to the VDD
supply at the same physical location as the IC itself.
Even if the IC and any external networks are powered
by the same supply, physical separation of the connect-
ing points can result in enough parasitic capacitance
and/or inductance in the power supply connections to
delay one power supply “routing” versus another.
5.7
Power Supply Routing and
Bypassing
Noise present on the VIN and VMIN inputs may cause
erroneous operation of the FAULT output. As a result,
these inputs should be bypassed with a 0.01 F capac-
itor mounted as close to the package as possible. This
is particularly true of VIN, which is usually driven from a
high impedance source (such as a thermistor). In addi-
tion, the VDD input should be bypassed with a 1 F
capacitor. Ground should be kept as short as possible.
To keep fan noise off the TC647 ground pin, individual
ground returns for the TC647 and the low side of the
fan current sense resistor should be used.
Design Example
Step 1. Calculate R1 and R2 based on using an NTC
having a resistance of 10 k
at TMIN (25°C)
and 4.65 k
R1 = 20.5 k
R2 = 3.83 k
Step 2. Set minimum fan speed VMIN = 1.8V.
Limit the divider current to 100 A from which
R5 = 33 k and R6 = 18 k
Step 3. Design the output circuit.
Maximum fan motor current = 250 mA.
Q1 beta is chosen at 50 from which
R7 = 800.
Q1
Q2
GND
VDD
RSENSE
RBASE
VOUT
Fan
a) Single Bipolar Transistor
Q1
GND
VDD
RSENSE
VOUT
C) N-Channel MOSFET
GND
VDD
RSENSE
RBASE
Fan
b) Darlington Transistor Pair
Fan
GND
+5V
Q1 *
VDD
VOUT
TC647
Fan
R2 *
2.2 k
R3 *
2.2
*Note: Value depends on the specific application and is shown for example only.
D1
12.0V
Zener
-12V
R4 *
10 k
相關PDF資料 |
PDF描述 |
|---|---|
| TC647VOART | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC648EOA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC648VOA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC649BEPA | BRUSHLESS DC MOTOR CONTROLLER, PDIP8 |
| TC648BEUA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC648 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert |
| TC648_13 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert |
| TC648B | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controllers With Auto-Shutdown, Fan Restart and FanSense⑩ Technology for Fault Detection |
| TC648BEOA | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Over-T Alert RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC648BEOA713 | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Over-T Alert RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。