- 您現在的位置：買賣IC網 > PDF目錄383931 > TC647 (Microchip Technology Inc.) PWM Fan Speed Controller with FanSense Technology PDF資料下載
參數資料
| 型號： | TC647 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | PWM Fan Speed Controller with FanSense Technology |
| 中文描述： | 與FanSense PWM風扇速度控制器技術 |
| 文件頁數： | 4/28頁 |
| 文件大?。?/td> | 478K |
| 代理商： | TC647 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
TC647
DS21447C-page 4
2002 Microchip Technology Inc.
2.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
PIN FUNCTION TABLE
2.1
Analog Input (V
IN
)
The thermistor network (or other temperature sensor)
connects to the V
IN
input. A voltage range of 1.25V to
2.65V (typical) on this pin drives an active duty cycle of
0% to 100% on the V
OUT
pin.
2.2
Analog Output (C
F
)
C
F
is the positive terminal for the PWM ramp generator
timing capacitor. The recommended C
F
is 1 μF for
30 Hz PWM operation.
2.3
Analog Input (V
MIN
)
An external resistor divider connected to the V
MIN
input
sets the minimum fan speed by fixing the minimum
PWM duty cycle (1.25V to 2.65V = 0% to 100%, typi-
cal). The TC647 enters shutdown mode when V
MIN
≤
V
SHDN
. During shutdown, the FAULT output is inactive
and supply current falls to 25 μA (typical). The TC647
exits shutdown mode when V
MIN
≥
V
REL
. See
Section 5.0, “Typical Applications”, for more details.
2.4
Ground (GND)
GND denotes the ground terminal.
2.5
Analog Input (SENSE)
Pulses are detected at the SENSE pin as fan rotation
chops the current through a sense resistor. The
absence of pulses indicates a fault.
2.6
Digital Output (FAULT)
The FAULT line goes low to indicate a fault condition.
When FAULT goes low due to a fan fault condition, the
device is latched in shutdown mode until deliberately
cleared or until power is cycled. FAULT may be con-
nected to V
MIN
if a hard shutdown is desired.
2.7
Digital Output (V
OUT
)
V
OUT
is an active high complimentary output that drives
the base of an external NPN transistor (via an appropri-
ate base resistor) or the gate of an N-channel MOS-
FET. This output has asymmetrical drive (see
Section 1.0, “Electrical Characteristics”).
2.8
Power Supply Input (V
DD
)
V
DD
may be independent of the fan’s power supply
(see Section 1.0, “Electrical Characteristics”).
Pin No.
Symbol
Description
1
2
3
4
5
6
7
8
V
IN
C
F
V
MIN
GND
SENSE
FAULT
V
OUT
V
DD
Analog Input
Analog Output
Analog Input
Ground Terminal
Analog Input
Digital (Open Collector) Output
Digital Output
Power Supply Input
相關PDF資料 |
PDF描述 |
|---|---|
| TC647EPA | PWM Fan Speed Controller with FanSense Technology |
| TC647EUA | PWM Fan Speed Controller with FanSense Technology |
| TC648VOA | Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert |
| TC648 | Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert |
| TC648E | Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC647_13 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controller with FanSensea?￠ Technology |
| TC647B | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controllers With Minimum Fan Speed, Fan Restart and FanSense⑩ Technology for Fault Detection |
| TC647BEOA | 功能描述:馬達/運動/點火控制器和驅動器 w/Rstrt & Flt Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC647BEOA713 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controllers With Minimum Fan Speed, Fan Restart and FanSense⑩ Technology for Fault Detection |
| TC647BEOATR | 功能描述:馬達/運動/點火控制器和驅動器 w/Rstrt & Flt Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發(fā)布緊急采購，3分鐘左右您將得到回復。