參數資料
型號： TC646VPA
廠商： Microchip Technology Inc.
英文描述： PWM Fan Speed Controller with Auto-Shutdown and FanSense⑩ Technology
中文描述： PWM風扇帶自動調速器關斷和FanSense⑩技術
文件頁數： 8/28頁
文件大?。?/td> 473K
代理商： TC646VPA
TC646
DS21446C-page 8
2002 Microchip Technology Inc.
4.0
SYSTEM BEHAVIOR
The flowcharts describing the TC646’s behavioral
algorithm are shown in Figure 4-1. They can be
summarized as follows:
4.1
Power-Up
(1) Assuming the device is not being held in auto-shut-
down mode (V
IN
> V
AS
)..........
(2) Turn V
OUT
output on for 32 cycles of the PWM
clock. This ensures that the fan will start from a
dead stop.
(3) During this Start-up Timer, if a fan pulse is
detected, branch to Normal Operation; if none are
received…
(4) Activate the 32-cycle Start-up Timer one more time
and look for fan pulse; if a fan pulse is detected,
proceed to Normal Operation; if none are
received…
(5) Proceed to Fan Fault.
(6) End.
4.2
Normal Operation
“Normal Operation” is an endless loop which may only
be exited by entering shutdown mode, auto-shutdown
mode or Fan Fault. The loop can be thought of as
executing at the frequency of the oscillator and PWM.
(1) Reset the missing pulse detector.
(2) Is the TC646 in shutdown or auto-shutdown
mode
If so...
a. V
OUT
duty cycle goes to zero.
b. FAULT is disabled.
c. Exit the loop and wait for V
IN
> (V
AS
+ V
HAS
) to
resume operation.
(3) If an over-temperature fault occurs (V
IN
> V
OTF
),
activate FAULT; release FAULT when
V
IN
< V
OTF
.
(4) Drive V
OUT
to a duty cycle proportional to V
IN
on
a cycle by cycle basis.
(5) If a fan pulse is detected, branch back to the
start of the loop (1).
(6) If the missing pulse detector times out …
(7) Activate the 3-cycle Diagnostic Timer and look
for pulses; if a fan pulse is detected, branch
back to the start of the loop (1); if none are
received…
(8) Activate the 32-cycle Start-up Timer and look for
pulses; if a fan pulse is detected, branch back to
the start of the loop (1); if none are received…
(9) Quit Normal Operation and go to Fan Fault.
(10) End.
4.3
Fan Fault
Fan fault is an infinite loop wherein the TC646 is
latched in shutdown mode. This mode can only be
released by a reset (i.e., V
IN
being brought below
V
SHDN
, then above (V
AS
+ V
HAS
), or by power-cycling).
(1) While in this state, FAULT is latched on (low) and
the
V
OUT
output is disabled.
(2) A reset sequence applied to the V
IN
pin will exit the
loop to Power-up.
(3) End.
相關PDF資料
PDF描述
TC646VOA PWM Fan Speed Controller with Auto-Shutdown and FanSense⑩ Technology
TC647EOA PWM Fan Speed Controller with FanSense Technology
TC647VOA PWM Fan Speed Controller with FanSense Technology
TC647VPA PWM Fan Speed Controller with FanSense Technology
TC647VUA PWM Fan Speed Controller with FanSense Technology
相關代理商/技術參數
參數描述
TC646VUA 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TC646VUA713 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TC647 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controller with FanSense Technology
TC647_13 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controller with FanSensea?￠ Technology
TC647B 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:PWM Fan Speed Controllers With Minimum Fan Speed, Fan Restart and FanSense⑩ Technology for Fault Detection
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*