參數資料
型號： TC530CPJ
廠商： Microchip Technology
文件頁數： 4/28頁
文件大?。?/td> 0K
描述： IC DATA ACQ SUBSYSTEM 28DIP
標準包裝： 15
類型： 數據采集系統（DAS）
分辨率（位）： 17 b
采樣率（每秒）： 6.5
數據接口： 串行
電壓電源： 單電源
電源電壓： 4.5 V ~ 5.5 V
工作溫度： 0°C ~ 70°C
安裝類型： 通孔
封裝/外殼： 28-DIP（0.300"，7.62mm）
供應商設備封裝： 28-DIP
包裝： 管件
其它名稱： Q1000542A
TC530/TC534
DS21433C-page 12
2007 Microchip Technology Inc.
5.0
TYPICAL APPLICATIONS
5.1
Programming the TC530/TC534
5.1.1
AZ AND INT PHASE DURATION
These two phases have equal duration determined by
the crystal (or external) frequency and the timer initial-
ization byte (LOAD VALUE). Timing is selected as
follows:
1.
Select Integration Time
Integration time must be picked as a multiple of
the period of the line frequency. For example,
TINT times of 33 ms, 66 ms and 132 ms
maximize 60 Hz line rejection.
2.
Estimate Crystal Frequency
Crystal frequencies as high as 2 MHz are
allowed. Crystal frequency is estimated using:
EQUATION 5-1:
3.
Calculate LOAD VALUE
EQUATION 5-2:
FIN can be adjusted to a standard value during this
step. The resulting base, -10 LOAD VALUE, must be
converted to a hexadecimal number and then loaded
into the serial port prior to initiating A/D conversion.
5.2
DINT and IZ Phase Timing
The duration of the DINT phase is a function of the
amount of voltage stored on the integrator capacitor
during INT and the value of VREF. The DINT phase is
initiated immediately following INT and terminated
when an integrator output zero crossing is detected. In
general, the maximum number of counts chosen for
DINT is twice that of INT (with VREF chosen at
VIN(MAX)/2).
5.3
System RESET
The TC530/TC534 must be forced into the AZ state
when power is first applied. A .01 F capacitor
connected from RESET to VDD (or external system
reset logic signal) can be used to momentarily drive
RESET high for a minimum of 100 ms.
5.4
Design Example
Figure 5-1 shows a typical TC530 interrupt-driven
application. Timing and component values are
calculated from equations and recommendations made
of this document. The EOC connection to the
processor INT input is for interrupt-driven applications
only. (In polled systems, the EOC output is available on
DOUT).
Given:
1.
Pick Integration time (TINT): 66 ms.
2.
Estimate crystal frequency.
EXAMPLE 5-1:
3.
Calculate LOAD VALUE
EXAMPLE 5-2:
4.
Calculate RINT.
EXAMPLE 5-3:
5.
Calculate CINT for maximum (4V) integrator out-
put swing:
2(RES)/TINT
Where:
RES
=
Desired Converter Resolution (in
counts)
FIN
=
Input Frequency (in MHz)
INT
=
Integration Time (in seconds)
[LOAD VALUE]10
256
TINT
() F
IN
()
1024
------------------------------
–
=
Required Resolution
(RES):
16-bits (65,536 counts.)
Maximum: VIN ±2V
Power Supply Voltage: +5V
60Hz System
FIN
2RES
TINT
------------
2 65536
66ms
----------------------- 2MHz
≈
==
LOAD VALUE
256
TINT
() F
IN
()
1024
------------------------------
–
128
[]
10
==
128
[]
10
80 hex
=
RINT
VINMAX
20
-------------------
2
20
------
100k
Ω
==
=
相關PDF資料
PDF描述
MS3108A20-33P CONN PLUG 11POS RT ANG W/PINS
M83723/83W1814N CONN RCPT 14POS WALL MT W/PINS
MAX180AEPL+ IC DAS 12BIT 100KSPS 40-DIP
M83723/83R1814N CONN RCPT 14POS WALL MT W/PINS
MS27473E22B55PD CONN PLUG 55POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
TC531000AP-F711 制造商:Toshiba America Electronic Components 功能描述:531000AP-F711
TC531001 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:1M BIT (128K WORD x 8 BIT) CMOS MASK ROM
TC531001CF 制造商:Toshiba America Electronic Components 功能描述:
TC531001CF-12 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:1M BIT (128K WORD x 8 BIT) CMOS MASK ROM
TC531001CF-15 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:1M BIT (128K WORD x 8 BIT) CMOS MASK ROM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*