參數資料
型號： TC510COG713
廠商： Microchip Technology
文件頁數： 3/38頁
文件大?。?/td> 0K
描述： IC ANALOG FRONT END 17BIT 24SOIC
標準包裝： 1,000
位數： 17
通道數： 1
功率（瓦特）： 18mW
電壓 - 電源，模擬： 5V
電壓 - 電源，數字： 4.5 V ~ 5.5 V
封裝/外殼： 24-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 24-SOIC
包裝： 帶卷 (TR)
2008 Microchip Technology Inc.
DS21428E-page 11
TC500/A/510/514
5.0
TC500/A/510/514 CONVERTER
OPERATION
The TC500/A/510/514 incorporates an auto-zero and
Integrator phase in addition to the input signal Integrate
and reference De-integrate phases. The addition of
these phases reduce system errors, calibration steps
and shorten overrange recovery time. A typical
measurement cycle uses all four phases in the
following order:
1.
Auto-zero.
2.
Input signal integration.
3.
Reference de-integration.
4.
Integrator output zero.
The internal analog switch status for each of these
phases is summarized in Table 5-1. This table
references the Typical Application.
TABLE 5-1:
INTERNAL ANALOG GATE STATUS
5.1
Auto-zero Phase (AZ)
During this phase, errors due to buffer, integrator and
comparator offset voltages are nulled out by charging
CAZ (auto-zero capacitor) with a compensating error
voltage.
The external input signal is disconnected from the
internal circuitry by opening the two SWI switches. The
internal input points connect to analog common. The
reference capacitor is charged to the reference voltage
potential through SWR. A feedback loop, closed around
the integrator and comparator, charges the capacitor
(CAZ) with a voltage to compensate for buffer amplifier,
integrator and comparator offset voltages.
5.2
Analog Input Signal Integration
Phase (INT)
The TC5XX integrates the differential voltage between
the VIN+ and VIN– inputs. The differential voltage must
be within the device’s Common mode range VCMR. The
input signal polarity is normally checked via software at
the end of this phase: CMPTR = 1 for positive polarity;
CMPTR = 0 for negative polarity.
5.3
Reference Voltage De-integration
Phase (DINT)
The previously charged reference capacitor is
connected with the proper polarity to ramp the
integrator output back to zero. An externally-provided,
precision timer is used to measure the duration of this
phase. The resulting time measurement is proportional
to the magnitude of the applied input voltage.
5.4
Integrator Output Zero Phase (IZ)
This phase ensures the integrator output is at 0V when
the auto-zero phase is entered, and that only system
offset voltages are compensated. This phase is used at
the end of the reference voltage de-integration phase
and MUST be used for ALL TC5XX applications having
resolutions of 12-bits or more. If this phase is not used,
the value of the auto-zero capacitor (CAZ) must be
about 2 to 3 times the value of the integration capacitor
(CINT) to reduce the effects of charge sharing. The
integrator output zero phase should be programmed to
operate until the output of the comparator returns high.
The overall timing system is shown in Figure 5-1.
Conversion Phase
SWI
SWR+SWR-SWZ
SWR
SW1
SWIZ
Auto-zero (A = 0, B = 1)
—
Closed
—
Input Signal Integration (A = 1, B = 0)
Closed
—
Reference Voltage De-integration
(A =1, B = 1)
—
*
Closed
—
Closed
—
Integrator Output Zero (A = 0, B = 0)
—
Closed
* Assumes a positive polarity input signal. SW–RI would be closed for a negative input signal.
相關PDF資料
PDF描述
MAX9018BEKA+T IC COMPARATOR DUAL SOT23-8
MAX987EXK+T IC COMPARATOR R-R SC70-5
TC500ACOE713 IC ANALOG FRONT END 17BIT 16SOIC
V375C2M50BG2 CONVERTER MOD DC/DC 2V 50W
TC500COE713 IC ANALOG FRONT END 16BIT 16SOIC
相關代理商/技術參數
參數描述
TC510COI 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC
TC510COI713 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC
TC510COIOI713 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Precision Analog Front Ends
TC510CPE 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Precision Analog Front Ends
TC510CPF 功能描述:電信線路管理 IC Prec Analog Frnt End RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*