- 您現在的位置：買賣IC網 > PDF目錄98169 > TC2574-VOETR 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | TC2574-VOETR |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | WIDE, SOIC-16 |
| 文件頁數： | 24/25頁 |
| 文件大?。?/td> | 212K |
| 代理商： | TC2574-VOETR |
TC2574
8
TC2574-1 1/6/00
0.5A Step-Down Switching Regulator
Procedure (Fixed Output Voltage Version) (Continued)
In order to simplify the switching regulator design, a step-by-step design procedure and examples are provided.
Procedure
Example
5. Output Capacitor Selection (COUT)
A. Since the TC2574 is a forward–mode switching regulator
with voltage mode control, its open loop 2–pole–1–zero
frequency characteristic has the dominant pole–pair deter
mined by the output capacitor and inductor values.
For stable operation and an acceptable ripple voltage,
(approximately 1% of the output voltage) a value
between 100
F and 470F is recommended.
B. Due to the fact that the higher voltage electrolytic
capacitors generally have lower ESR (Equivalent Series
Resistance) numbers, the output capacitor’s voltage
rating should be at least 1.5 times greater than the output
voltage. For a 5.0Vregulator, a rating at least 8.0V is a
appropriate, and a 10Vor 16V rating is recommended.
5. Output Capacitor Selection (COUT )
A. COUT = 100F to 470F standard aluminium
electrolytic.
B. Capacitor voltage rating = 20V.
Procedure (Adjustable Output Version: TC2574-ADJ)
Procedure
Example
Given Parameters:
VOUT = Regulated Output Voltage
VIN (max) = Maximum DC Input Voltage
ILOAD (max) = Maximum Load Current
1. Programming Output Voltage
To select the right programming resistor R1 and R2
value (see Figure 2) use the following formula:
VOUT = VREF
(1.0 + R2 ) where V
REF = 1.23V
R1
Resistor R1 can be between 1.0k
and 5.0k. (For best
temperature coefficient and stability with time, use 1% metal
film resitors).
R2 = R1
( VOUT – 1.0)
VREF
2. Input Capacitor Selection (CIN )
To prevent large voltage transients from appearing at the
input and for stable operation of the converter, an aluminium
or tantalum electrolytic bypass capacitor is needed between
the input pin +VIN and ground pin GND. This capacitor
should be located close to the IC using short leads. This
capacitor should have a low ESR (Equivalent Series
Resistance) value. For additional information see input
capacitor section in the “EXTERNAL COMPONENTS”
section of this data sheet.
Given Parameters:
VOUT = 24V
VIN (max) = 40V
ILOAD (max) = 0.4A
2. Input Capacitor Selection (CIN )
A 22
F aluminium electrolytic capacitor located near the
input and ground pin provides sufficient bypassing.
1. Programming Output Voltage (selecting R1 and R2)
Select R1 and R2
VOUT = 1.23
(1.0 + R2 ) Select R1 = 1.0k
R1
R2 = R1
( VOUT – 1.0) = 1.0k ( 10V – 1.0)
VREF
1.23V
R1 = 18.51k
, choose a 18.7k metal film resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| TC2575-12.0VAT | 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PSFM5 |
| TC271-40 | SPECIALTY ANALOG CIRCUIT, CDIP22 |
| TC33025VOETR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TC33163EOETR | 3.4 A SWITCHING CONTROLLER, 55 kHz SWITCHING FREQ-MAX, PDSO16 |
| TC33163EOETR | 3.4 A SWITCHING REGULATOR, 55 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC2574VPA | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TC2574-VPA | 制造商:TELCOM 制造商全稱:TelCom Semiconductor, Inc 功能描述:0.5A Step-Down Switching Regulator |
| TC2575 | 制造商:TELCOM 制造商全稱:TelCom Semiconductor, Inc 功能描述:1.0A Step-Down Switching Regulator |
| TC2575-12.0VAT | 制造商:TELCOM 制造商全稱:TelCom Semiconductor, Inc 功能描述:1.0A Step-Down Switching Regulator |
| TC2575-3.3VAT | 制造商:TELCOM 制造商全稱:TelCom Semiconductor, Inc 功能描述:1.0A Step-Down Switching Regulator |
發布緊急采購，3分鐘左右您將得到回復。