- 您現在的位置：買賣IC網 > PDF目錄383914 > TC1303B-FL0EMFTR (Microchip Technology Inc.) 500 mA Synchronous Buck Regulator, + 300 mA LDO with Power-Good Output PDF資料下載
參數資料
| 型號： | TC1303B-FL0EMFTR |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 500 mA Synchronous Buck Regulator, + 300 mA LDO with Power-Good Output |
| 中文描述： | 500毫安同步降壓穩壓器，300 mA的LDO具有電源就緒輸出 |
| 文件頁數： | 18/30頁 |
| 文件大?。?/td> | 441K |
| 代理商： | TC1303B-FL0EMFTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
TC1303B
DS21949A-page 18
2005 Microchip Technology Inc.
5.0
APPLICATION
CIRCUITS/ISSUES
5.1
Typical Applications
The TC1303B 500 mA buck regulator + 300 mA LDO
with power-good operates over a wide input voltage
range (2.7V to 5.5V) and is ideal for single-cell Li-Ion
battery-powered applications, USB-powered applica-
tions, three-cell NiMH or NiCd applications and 3V to
5V regulated input applications. The 10-pin MSOP and
3X3 DFN packages provide a small footprint with
minimal external components.
5.2
Fixed Output Application
A typical V
OUT1
fixed output voltage application is
shown in “
Typical Application Circuits”
on page 3. A
4.7 μF V
IN1
ceramic input capacitor, 4.7 μF V
OUT1
ceramic capacitor, 1.0 μF ceramic V
OUT2
capacitor and
4.7 μH inductor make up the entire external component
solution for this dual-output application. No external
dividers or compensation components are necessary.
For this application, the input voltage range is 2.7V to
4.2V, V
OUT1
= 1.5V at 500 mA, while V
OUT2
= 2.5V at
300 mA.
5.3
Adjustable Output Application
A typical V
OUT1
adjustable output application is also
shown in “
Typical Application Circuits”
on page 3.
For this application, the buck regulator output voltage is
adjustable by using two external resistors as a voltage
divider. For adjustable output voltages, it is recom-
mended that the top resistor divider value be 200 k
Ω.
The bottom resistor divider can be calculated using the
following formula:
EQUATION 5-1:
Example:
R
TOP
= 200 k
Ω
V
OUT1
= 2.1V
V
FB
= 0.8V
R
BOT
= 200 k
Ω
x (0.8V/(2.1V – 0.8V))
R
BOT
= 123 k
Ω
(Standard Value = 121 k
Ω
)
For adjustable output applications, an additional R-C
compensation is necessary for the buck regulator
control loop stability. Recommended values are:
R
COMP
= 4.99 k
Ω
C
COMP
= 33 pF
An additional V
IN2
capacitor can be added to reduce
high frequency noise on the LDO input voltage pin
(V
IN2
). This additional capacitor (1 μF on page 3) is not
necessary for typical applications.
5.4
Input and Output Capacitor
Selection
As with all buck-derived dc-dc switching regulators, the
input current is pulled from the source in pulses. This
places a burden on the TC1303B input filter capacitor.
In most applications, a minimum of 4.7 μF is recom-
mended on V
IN1
(buck regulator input voltage pin). In
applications that have high source impedance or have
long leads (10 inches) connecting to the input source,
additional capacitance should be used. The capacitor
type can be electrolytic (aluminum, tantalum, POSCAP,
OSCON) or ceramic. For most portable electronic
applications, ceramic capacitors are preferred due to
their small size and low cost.
For applications that require very low noise on the LDO
output, an additional capacitor (typically 1 μF) can be
added to the V
IN2
pin (LDO input voltage pin).
Low ESR electrolytic or ceramic can be used for the
buck regulator output capacitor. Again, ceramic is
recommended because of its physical attributes and
cost. For most applications, a 4.7 μF is recommended.
Refer to Table 5-1 for recommended values. Larger
capacitors (up to 22 μF) can be used. There are some
advantages in load step performance when using
larger value capacitors. Ceramic materials X7R and
X5R have low temperature coefficients and are well
within the acceptable ESR range required.
TABLE 5-1:
TC1303B RECOMMENDED
CAPACITOR VALUES
R
BOT
R
TOP
V
V
OUT1
V
FB
–
--------------------------------
×
=
C(V
IN1
)
4.7 μF
none
C(V
IN2
)
none
none
C
OUT1
4.7 μF
22 μF
C
OUT2
1 μF
10 μF
min
max
相關PDF資料 |
PDF描述 |
|---|---|
| TC1303B-FL0EUN | 500 mA Synchronous Buck Regulator, + 300 mA LDO with Power-Good Output |
| TC1303B-FL0EUNTR | 500 mA Synchronous Buck Regulator, + 300 mA LDO with Power-Good Output |
| TC1303B-FL1EMF | 500 mA Synchronous Buck Regulator, + 300 mA LDO with Power-Good Output |
| TC1303B-FL1EMFTR | 500 mA Synchronous Buck Regulator, + 300 mA LDO with Power-Good Output |
| TC1303B-FL1EUN | 500 mA Synchronous Buck Regulator, + 300 mA LDO with Power-Good Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC1303B-IA0EMF | 功能描述:低壓差穩壓器 - LDO PWM/LDO combo w/PG RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TC1303B-IA0EMFTR | 功能描述:低壓差穩壓器 - LDO PWM/LDO combo w/PG RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TC1303B-IA0EUN | 功能描述:低壓差穩壓器 - LDO PWM/LDO combo w/PG RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TC1303B-IA0EUNTR | 功能描述:低壓差穩壓器 - LDO PWM/LDO combo w/PG RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TC1303B-PA0EMF | 功能描述:低壓差穩壓器 - LDO PWM/LDO combo w/PG RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。