- 您現在的位置：買賣IC網 > PDF目錄98167 > TC1276-20ENBTR 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 PDF資料下載
參數資料
| 型號： | TC1276-20ENBTR |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| 封裝： | SOT-23B, 3 PIN |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 466K |
| 代理商： | TC1276-20ENBTR |
2002 Microchip Technology Inc.
DS21383B-page 5
TC1275/TC1276/TC1277
3.2
VCC Transient Rejection
The TC1275/TC1276/TC1277 provides accurate VCC
monitoring and reset timing during power-up, power-
down, and brownout/sag conditions, and rejects
negative-going transients (glitches) on the power
supply line. Figure 3-5 shows the maximum transient
duration vs. maximum negative excursion (overdrive)
for glitch rejection. Any combination of duration and
overdrive that lays under the curve will not generate a
reset signal. Combinations above the curve are
detected as a brownout or power-down. Transient
immunity can be improved by adding a capacitor in
close proximity to the VCC pin of the TC1275/TC1276/
TC1277.
3.3
RESET Signal Integrity During
Power-Down
The TC1275 RESET output is valid to VCC =1.2V.
Below this voltage the output becomes an "open
circuit" and does not sink current. This means CMOS
logic inputs to the
P will be floating at an undeter-
mined voltage. Most digital systems are completely
shut down well above this voltage. However, in situa-
tions where RESET must be maintained valid to VCC =
0V, a pull-down resistor must be connected from
RESET to ground to discharge stray capacitances and
hold the output low (Figure 3-6). This resistor value,
though not critical, should be chosen such that it does
not appreciably load RESET under normal operation
(100k
will be suitable for most applications). Similarly,
a pull-up resistor to VCC is required for the TC1277 to
ensure a valid high RESET for VCC below 1.8V.
FIGURE 3-5:
MAXIMUM TRANSIENT
DURATION VS.
OVERDRIVE FOR GLITCH
REJECTION AT 25°C
FIGURE 3-6:
ENSURING RESET VALID
TO VCC =0V
RESET COMPARATOR OVERDRIVE,
[V
CCTP - VCC] (mV)
500
300
200
400
100
0
1
10
100
1000
MAXIMUM
TRANSIENT
DURATION
(
sec)
TA
°C
VTH
Duration
Overdrive
VCC
TC1275/6/7
TC1275
VCC
R1
100k
RESET
GND
相關PDF資料 |
PDF描述 |
|---|---|
| TC1277-5ENB713 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TC1275-5ENB | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TC1276-15ENB713 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TC1275-10ENB713 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TC1275-15ENB713 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC1276-5ENB | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:3-Pin Reset Monitors for 3.3V Systems |
| TC1276-5ENBTR | 功能描述:監控電路 3-Pin for 3.3V Syst RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| TC1276-XENB | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:3-Pin Reset Monitors for 3.3V Systems |
| TC1277 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:3-Pin Reset Monitors for 3.3V Systems |
| TC1277-10ENB | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:3-Pin Reset Monitors for 3.3V Systems |
發布緊急采購，3分鐘左右您將得到回復。