- 您現在的位置：買賣IC網 > PDF目錄359287 > TB6585FG BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 PDF資料下載
參數資料
| 型號： | TB6585FG |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| 封裝： | 0.450 INCH, 0.65 MM PITCH, PLASTIC, HSOP-36 |
| 文件頁數： | 14/25頁 |
| 文件大小： | 303K |
| 代理商： | TB6585FG |
TB6585FG
2008-03-04
14
<
Sine-Wave PWM Signal Generation
>
The modulated waveform is generated using the Hall signals. The sine-wave PWM signal is then generated
by comparing the modulated waveform with the triangular wave.
The time between the rising edges (falling edges) and the immediately-following falling edges (rising edges)
of any of the three Hall signals (interval of 60 electrical degrees) are calculated by the counter. This period is
used for data generation of the next 60-electrical-degree interval.
The modulated waveform of 60-electrical-degree interval consists of 32 data items. The time period for a
single data item is 1/32 of the previous 60-electrical-degree interval. The modulated waveform advances by
this period. (Operating waveforms when CW/CCW
=
Low)
As illustrated above, the modulated waveform ) (1)’advances by 1/32 of the period between the rising edge
(
) of HU and the falling edge (
) of HW. Likewise, the modulated waveform (2)’ advances by 1/32 of the
period between the falling edge (
) of HW and the rising edge (
If the next edge does not occur even after completing the generation of 32 data, data for the next
60-electrical-degree interval are generated based on the same time period until the next edge occurs.
) of HV.
Also, the phase alignment with the modulated waveform is performed at every zero-cross point. The
modulated waveform is reset by being synchronized with the rising and falling edges of the position
detection signal at every 60 electrical degrees. Therefore, the modulated waveform becomes discontinuous
Sw
HUP
HVP
HWP
S
U
S
V
(5)
(2)
(6)
(1)
(3)
(6)
(1)
(2)
(3)
*:
Though the HUP, HVP and
HWP pins are Hall effect
inputs, they are indicated as
square waveforms for the
sake of simplicity.
*
t
S
V
(1)’
1
2
3
4
5
6
30
31
32
32 data
*
t
=
t (1)
×
1/32
相關PDF資料 |
PDF描述 |
|---|---|
| TC1240AECHTR | SWITCHED CAPACITOR CONVERTER, 125 kHz SWITCHING FREQ-MAX, PDSO6 |
| TC1264-3.0VEBRT | 3 V FIXED POSITIVE LDO REGULATOR, 1.3 V DROPOUT, PSSO2 |
| TC1264-2.5VEBRT | 2.5 V FIXED POSITIVE LDO REGULATOR, 1.3 V DROPOUT, PSSO2 |
| TC1264-3.0VAB | 3 V FIXED POSITIVE LDO REGULATOR, 1.3 V DROPOUT, PSFM3 |
| TC1264-3.0VEB | 3 V FIXED POSITIVE LDO REGULATOR, 1.3 V DROPOUT, PSSO3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB6585FG(O,8,EL) | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase PWM DRVR 4.5 to 42V 20mA RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6585FG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 Brushless DC Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6585FG(OEL) | 制造商:Toshiba America Electronic Components 功能描述:BRUSHLESS DC MOTOR DRIVER 45V 1.8MA 制造商:Toshiba America Electronic Components 功能描述:MOTOR DRIVER BRUSHLESS 45V 1.8A |
| TB6585FTG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA Bi-CMOS Integrated Circuit Silicon Monolithic |
| TB6585FTG(O,8,EL) | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase PWM DRVR 4.5 to 42V 20mA RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。