參數資料
型號： TB6560AFG
元件分類： 運動控制電子
英文描述： STEPPER MOTOR CONTROLLER, 2.5 A, PQFP64
封裝： 10 X 10 MM, 0.50 MM PITCH, ROHS COMPLIANT, PLASTIC, QFP-64
文件頁數： 21/34頁
文件大?。?/td> 481K
代理商： TB6560AFG
TB6560AHQ/AFG
2009-07-10
28
1. Power-on Sequence with Control Input Signals
Turn on VDD. Then, when the VDD voltage has stabilized, turn on VMA/B.
Hold the control input pins Low while turning on VDD and VMA/B.
(All the control input pins are internally pulled down.)
After VDD and VMA/B completely stabilizes at the rated voltages, the RESET and ENABLE pins can be
set High. If this sequence is not properly followed, the IC may not operate correctly, or the IC and the
peripheral parts may be damaged.
When RESET is released High, the CLK signal is applied and excitation is started. Only after ENABLE
is also set High, outputs are enabled. When only RESET is set High, outputs are disabled and only the
internal counter advances. Likewise, when only ENABLE is set High, the excitation will not be performed
even if the CLK signal is applied and the outputs will remain in the initial state.
An example of a control input sequence is shown below.
A power-off sequence should be the reverse of this sequence.
<Recommended Control Input Sequence>
2. Power Dissipation
The power dissipation of the IC can be calculated by the following equation:
P
= VDD × IDD + IOUT × IOUT × Ron × 2 phases
The higher the ambient temperature, the smaller the power dissipation.
Examine the PD-Ta characteristic curve to determine if there is a sufficient margin in the thermal design.
3. Treatment of Heat-Radiating Fin
The heat-radiating fin pins of the TB6560AHQ/AFG (backside) are electrically connected to the backside of
the die. Thus, if a current flows to the fin, the IC may malfunction. If there is any possibility of a voltage
being generated between grounds and the fin, the fin pins should either be connected to ground or
insulated.
4. Thermal Shutdown (TSD)
When the die temperature reaches 170°C (typ.), the thermal shutdown circuit is tripped, switching the
outputs to off. There is a variation of about
±20°C in the temperature at which the thermal shutdown
circuit is tripped.
Output
Z
Output current setting
Internal current setting
OUT
ENABLE
H
L
H
L
RESET
H
L
CLK
Internal current setting: Disabled;
Output OFF
Internal current setting: Enabled
相關PDF資料
PDF描述
TB6560AHQ STEPPER MOTOR CONTROLLER, 3.5 A, PZFM25
TB6561NG BRUSH DC MOTOR CONTROLLER, 1.5 A, PDIP24
TB6581HG BRUSHLESS DC MOTOR CONTROLLER, 2 A, PZIP25
TB6582FG BRUSHLESS DC MOTOR CONTROLLER, 0.002 A, PQFP52
TB6592FLG BRUSH DC MOTOR CONTROLLER, 0.8 A, PQCC24
相關代理商/技術參數
參數描述
TB6560AFG(O) 功能描述:馬達/運動/點火控制器和驅動器 Stepping Motor Drivr RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TB6560AFG(O,8) 功能描述:馬達/運動/點火控制器和驅動器 PWM Chopper Type Bipolar 40 VDSS RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TB6560AFG(O8) 制造商:Toshiba America Electronic Components 功能描述:IC MOTOR DRIVER STEPPER 3.5A HQFP-64 制造商:Toshiba America Electronic Components 功能描述:IC STEPPER MOTOR DRIVER 40V 3.5A
TB6560AFTG(O,8,EL) 功能描述:馬達/運動/點火控制器和驅動器 PWM Chopper Type Bipolar 40 VDSS RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TB6560AHQ 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:PWM Chopper-Type Bipolar Driver IC for Stepping Motor Control
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*