- 您現在的位置：買賣IC網 > PDF目錄98167 > TB6549HQ BRUSH DC MOTOR CONTROLLER, 5 A, ZIP25 PDF資料下載
參數資料
| 型號： | TB6549HQ |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 5 A, ZIP25 |
| 封裝： | 1MM PITCH, HZIP-25 |
| 文件頁數： | 21/22頁 |
| 文件大?。?/td> | 377K |
| 代理商： | TB6549HQ |
TB6549FG/PG/HQ
2010-07-13
8
3. Internal Constant-Voltage (5 V) Circuit
This IC includes a 5 V power supply for control circuit.
A capacitor for prevention of oscillation should be connected to S-GND associated with the pin Vreg.
No other loads should be connected to pin Vreg.
This IC has a power monitoring function and turns the output OFF when Vreg goes down to 3.0 V
(design target value) or less. With a hysteresis of 0.3 V (design target value), the output are turned ON
when Vreg again reaches 3.3 V (design target value).
4. Charge Pump Circuit
This IC has a charge pump circuit for driving the gate for the upper power transistor in the output
circuit. A voltage of VCC + 5 V (typ.) is generated by connecting an external capacitor to this IC.
It takes about 2 ms to boost VcpA up VCC + 5 V (typ.) after the switching of the input signal from the
standby pin (while CcpA = 0.22
μF, and CcpB and CcpC are connected through 0.01 μF).
The proper capacitance of the external capacitor varies depending on the VCC value. Thus, determine
the constant by referring to the following data. The value of the capacitor between CcpB and CcpC
should be such that, while the motor is being driven, the voltage on the CcpA pin will be kept constant,
typically at VCC + 5 V. (If a reduced VCC level causes the voltage on CcpA to start to fall, please adjust
this capacitance value accordingly.)
<External capacitor>
VCC
Between CcpB and CcpC
Between CcpA and GND
10 V to 15 V
0.01
μF to 0.047 μF
0.22
μF
15 V to 27 V
0.01
μF
0.22
μF
Reference oscillation is performed by using the internal capacitor.
VCC
Vreg
VCC
CcpC
VCC
CcpB
CcpA
相關PDF資料 |
PDF描述 |
|---|---|
| TB6551FAG | BRUSHLESS DC MOTOR CONTROLLER, PDSO24 |
| TB6552FL | BRUSH DC MOTOR CONTROLLER, 1 A, PQCC24 |
| TB6552FN | BRUSH DC MOTOR CONTROLLER, 1 A, PDSO16 |
| TB6559FG | BRUSH DC MOTOR CONTROLLER, 2.5 A, PDSO16 |
| TB6560AFG | STEPPER MOTOR CONTROLLER, 2.5 A, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB6549HQ(O) | 功能描述:馬達/運動/點火控制器和驅動器 30V Bridge DRVR 3.5A 1.0 Ohm low RDS RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6549P | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Full-Bridge Driver IC for DC Motors |
| TB6549PG | 功能描述:馬達/運動/點火控制器和驅動器 Bridge Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6549PG(O) | 功能描述:馬達/運動/點火控制器和驅動器 30V PWR Supply 3.5A Full Bridge DRVR PWM RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6551F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:3-Phase Full-Wave Sine-Wave PWM Brushless Motor Controller |
發布緊急采購，3分鐘左右您將得到回復。