- 您現在的位置：買賣IC網 > PDF目錄384949 > TB62732FU (Toshiba Corporation) The step up type DC-DC converter only for white LED driver lighting PDF資料下載
參數資料
| 型號： | TB62732FU |
| 廠商： | Toshiba Corporation |
| 元件分類： | LED驅動器 |
| 英文描述： | The step up type DC-DC converter only for white LED driver lighting |
| 中文描述： | 唯一的白光LED驅動器照明加強型DC - DC轉換 |
| 文件頁數： | 6/15頁 |
| 文件大?。?/td> | 177K |
| 代理商： | TB62732FU |
TOSHIBA
T B 6 2 7 3 2 F U
27, Feb 2002 (Ver.04)
6
Fig 4 : burst control wave form
THE STAE OF THE PEAK CURRENT CONTROL
The peak current control is repeat in the control the waveform which showed it in the Fig 3.
The current pulse of the Fig 3 is a charging current on the output capacitor C2.
It is supplied to LED as a discharge current on the output side capacitor, and it through the R_sens to GND.
And, as for the charging voltage waveform of the output capacitor C2, it returns in the IC from the K terminal.
The internal circuit which the K terminal should be input from controls the current pulses so that the
average voltage value of the voltage wave form which it could get may become 53 mV (typ).
The constant current is controlled as a result as an average electric current value. Therefore, when R_sens = 2.7
ohm is connected, the average current value of (53 mV /2.7 ohms) = 19.6 mA can get it.
This IC is designed for the purpose of supplying the power 320 mW (min).
Generally it is a step up inductance 6.8 uH to the load power 320 mW. And, when the load electric power is small, it
can be done small for the inductance.
As a condition about the LED load between the generator terminal and the K terminal,
Please keep the condition in Vin (Vcc) < LED VF total.
There are no relations with the control of the IC, and LED is always turned on.
STANDBY MODE OPERATION
The SHDN terminal set-up the normal operation and the standby operation. The lighting operation is possible in
the "L" level in the stop (at the standby mode), the "H" level. Still, consumption supply current in the standby mode
is 1.2uA (max).
A-terminal voltage
A-terminal current
(External inductor current)
K-terminal voltage
(Waveform of current for cap. charge)
Maximum On pulse
width = 85%
I A( peak )
LED Vf
Switching frequency fOSC = 1MHz
It stabilizes it in the set Io
with lowering IA (peak).
It stabilizes it in the set Io
with lowering IA (peak).
相關PDF資料 |
PDF描述 |
|---|---|
| TB6500AH | 2 PHASE BIPOLAR STEPPER + FULL BRIDGE DRIVER |
| TB6500 | 2 PHASE BIPOLAR STEPPER + FULL BRIDGE DRIVER |
| TB6551FG | 3-Phase Full-Wave Sine-Wave PWM Brushless Motor Controller |
| TB6556FG | 3-Phase Full-Wave Sine-Wave PWM Brushless Motor Controller |
| TB6556F | 3-Phase Full-Wave Sine-Wave PWM Brushless Motor Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB62732FUG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Step-up DC/DC Converter for White LED Driver |
| TB62733FTG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Charge Pump type DC/DC Converter for White LED Driver |
| TB62734FMG | 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:Step Up Type DC-DC Converter for White LED |
| TB62736FUG | 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:Step-up Type DC-DC Converter for White LEDs |
| TB62736FUG(O,EL) | 功能描述:LED照明驅動器 White LED Driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。