- 您現在的位置：買賣IC網 > PDF目錄382574 > TB62731FUG (Toshiba Corporation) Step-up DC-DC Converter for White LED Driver PDF資料下載
參數資料
| 型號： | TB62731FUG |
| 廠商： | Toshiba Corporation |
| 元件分類： | LED驅動器 |
| 英文描述： | Step-up DC-DC Converter for White LED Driver |
| 中文描述： | 升壓型DC - DC轉換器，用于白光LED驅動器 |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 250K |
| 代理商： | TB62731FUG |
TB62731FUG
2006-06-14
6
Figure 3 Burst Control Waveforms
Burst Control
Burst control is control of the number of current pulses, shown in the graph on the previous page.
Control is repeated in desired cycles. The current pulse in the graph is the charged current on capacitor 2 (C2)
for output.
The current pulse is supplied to the LED as current discharged from the output-side capacitor. The current
pulse flows to GND via R_sens.
The waveform of the voltage charged on the output-side capacitor is fed back to the IC from pin K via C2.
The internal circuit which uses pin K for input controls the number of current pulses so that the mean voltage
value of the obtained voltage waveform is 36 mV. As a result, the output current is controlled as the constant
current (
=
mean current).
Connecting R_sens
=
1.8
obtains the mean current (36 mV
÷
1.8
=
20 mA).
Current is controlled by PFM (pulse frequency modulation) because the time when the output pulse is
generated varies (increases/decreases).
A prerequisite is that the input power from V
IN
is larger than the output power to the LED load. The
constant current is maintained by fixing a pulse stop time of 7.5~15
μ
s and increasing/decreasing the number of
current pulses. The number of current pulses is fewer when the input power exceeds the output power, larger
when the input power is less than the output power.
The burst frequency (pulse generation frequency) at controlled constant current is calculated as follows:
fburst [Hz]
=
(number of current pulses x (1/275~1/350 kHz)
+
pulse stop time (7.5~15
μ
s) . . . formula 1
The IC is designed to supply a load power of 320 mW (min).
Generally, a step-up inductance of 47
μ
H is used for optimum design for the load power of 320 mW. When the
load power is small, the inductance must be small.
Make sure the following condition for LED load between pins A and K is satisfied:
V
IN
(V
CC
)
<
LED Vf total
Note that, regardless of control by the IC, LEDs are always on.
Pin A voltage
Pin A current (external
inductance current)
Pin K voltage (current
charged on capacitor)
Pulse output time
width f
OSC
=
350 kHz
Maximum duty width for
inductor on: 83.3% of f
OSC
Pulse stop time width:
7.5
μ
s (min)~15
μ
s (max)
Repetition of waveforms at left
I A (peak)
=
240 mA (typ.)
相關PDF資料 |
PDF描述 |
|---|---|
| TB62732FUG | Step-up DC/DC Converter for White LED Driver |
| TB62801FG | Linear CCD Clock Driver |
| TB62801F | Linear CCD Clock Driver |
| TB6520PG | PWM TYPE 3−PHASE FULL−WAVE SENSORLESS MOTOR CONTROLLER |
| TB7001FL | For high current and low voltage applications Synchronous buck converter module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB62732FU | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:The step up type DC-DC converter only for white LED driver lighting |
| TB62732FUG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Step-up DC/DC Converter for White LED Driver |
| TB62733FTG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Charge Pump type DC/DC Converter for White LED Driver |
| TB62734FMG | 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:Step Up Type DC-DC Converter for White LED |
| TB62736FUG | 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:Step-up Type DC-DC Converter for White LEDs |
發布緊急采購，3分鐘左右您將得到回復。